Electronic Circuits Schematics Projects




low pass filter subwoofer

Rating: 9.00/10 (39Votes cast)

Category: Audio Circuits / Audio Filters
This circuit is also crossed to: Preamplifiers , Tone Balance , Stereo Circuits
Views: 1715
Rank: 0

The acoustic filters are met in various points in the sound systems. The knownest application they are the filters baxandal for regulating tone low and high frequencies and filters crossover where the acoustic region is separated in subareas, in order to it leads the corresponding loudspeakers. The application that to you we propose is a simple filter of region that limits the acoustic region (20-20000Hz) in the region 20-100Hz.The manufacture end needs a circuit of catering with operational tendency of catering equal with ±12. the operational amplifiers that constitute the active elements for this circuits of are double operational type as the TL082 and NE5532. The operation visit page.

The manufacture end needs a circuit of catering with operational tendency of catering equal with ±12. the operational amplifiers that constitute the active elements for this circuits of are double operational type as the TL082 and NE5532. The operation http://www.free-circuit-diagrams.com/audio/page-1/7/low-pass-filter-subwoofer

Related circuits

Voice Disguiser Circuit

A complete schematic diagram of the voice disguiser is shown. Microphone MIC1 picks up the voice signal and feeds it to an audio amplifier, consisting of Ql and Q2, and a few support components. The amplifier has a low-pass gain response that limits the voice frequencies to 5 kHz or lower. The...



Voice Scrambler/Descrambler

This circuit uses an NE602 as an inversion mixer. U2 is set to run at about 2.5 to 3.5 kHz. U3 drives a loudspe



Active band-reject filter

A filter with a band-reject characteristic is frequently referred to as a notch filter. A typical circuit using a µ 741 is the unity-gain configuration for this type of active filter shown. The filter response curve shown is a second-order band-reject filter with a notch frequency of 3 kHz....



Adjustable notch filter

In applications where the rejected signal might deviate slightly from the null on the notch network, it is advantageous to lower the Q of the network. This insures some rejection over a wider range of input frequencies. The figure shows a circuit where the Q may be varied from 0.3 to 50. A...



Four-Output Filter Circuit

The classic state-variable (two-integrator) filter (see Fig. A) is famous for its insensitivity to device parameter tolerances, as well as its ability to provide three simultaneous separate outputs: high pass, bandpass, and low pass. These advantages often offset the fact that a quad operational...



Universal Compander

Signetics" type NE575 compander IC is intended primarily for use with battery power supplies of 3 to 7 V (max. 8 V). It



Bandpass filter

The input signal is applied through R3 to the inverting input of the summing amplifier and the output is taken from the first integrator. The summing amplifier will maintain equal voltage at the inverting and non-inverting inputs. Defining 1/R1C1 as 1 and 1/R2C2 as u>2> th^ is now a convenient...



Attenuator schematic

Two low voltage, low power zeners are used to control electronically the level of an audio signal. The attenuation range is from 6 to 58dB for an input current from 0.042 to 77mA corresponding to a control voltage from 2.7 to 7.5V. If control voltage is limited to 5V, the attenuation is around...



What is a low pass filter? Passive RC low pass filter tutorial!

How to Construct a Low-Pass Filter Circuit on a Protoboard


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits