Stereo Circuits
- Page 5-
This a simple stereo electret microphone pre amplifier circuit. For maximum performance, use solid capacitors or film capacitors and metal film resistors. Here the simple audio mic pre amplifier circuit based on single IC LM358. The circuit is very simple,.... -
Stereo tube amplifier circuit which is built based 5 power tubes of 6SQ7-GT, 6V6-GT and 5Y3-GT. This circuit generates up to 4 watts audio output each channel.. -
USB Powered, Stereo PC Multimedia Speaker Circuit Diagram. This circuit is powered by 5V DC source obtainable from the USB port of the Computer. When electrical power switch S1 is turned to on` position, 5V power supply is extended towards the circuit and.... -
This is the latest BH1417 FM Transmitter architecture from RHOM that includes a lot of appearance in one baby package. It comes with pre-emphasis, limiter so that the music can be transmitted at the aforementioned audio level, stereo encoder for stereo.... -
This is the circuit diagram of USB powered computer speaker, or it widely known as multimedia speakers for PCs. The circuit has single-chipbased design, low-voltage electrical power supply, compatibility with USB power from computer, simple heat-sinking,.... -
The following schematic shows 12 W Bridge Amplifier circuit diagram as an application of the TDA2007A a class AB dual audio power amplifier which is designed for stereo application in music centers, TV receivers and portable radios. According to the.... -
3 Watt stereo amplifier circuit using MAX 7910 IC. The MAX9710 a stereo audio power amplifier IC capable of delivering 3Watts of out put to 4 Ohm loads. MAX9710 can be operated from a single 4. 5V to 5. 5V power supply, makes it ideal for hand held.... -
This circuit is used to convert a mono audio signal into a stereo signal that can be panned between the left and right channel by a 0-10V control signal, it is intended for analog synthesizer systems... -
Using a mobile phone while driving is dangerous. It is also against the law. However, you can use your mobile phone as a powerful music player with the help of a stereo power amplifier. This does away with the need of a sophisticated in-dash car music.... -
This project is related to the other tube amplifier projects I have posted. It has more than a casual similarity to the first Push-Pull EL84 (6BQ5) Oddwatt project from nearly two years ago. Both tube amplifier projects use EL84 / 6BQ5 tubes and the earlier.... -
This is the circuit diagram of USB powered computer speaker, or it widely known as multimedia speakers for PCs. The circuit has single-chipbased design, low-voltage electrical power supply, compatibility with USB power from computer, simple heat-sinking,.... -
This is an excellent Hi-Fi Stereo PLL FM Transmitter, the audio source can be the computer, sound card, game consoles, CD, DVD, MP3, stereo mixer for stereo audio signal modulated emission transmission, the board also contains two mic amplifier, with the.... -
Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils and inductors. This LC Meter allows to measure incredibly small inductances making it perfect tool for making all types of RF coils and inductors. LC Meter can.... -
I built my first power amplifier when I was still in secondary school. The circuit was made of transistors, didn`t provide much power and had an ugly PCB. Around the same time I got access to a datasheet of TDA1524, a tone/volume control circuit, and I.... -
A high quality stereo FM transmitter circuit is shown here. The circuit is based on the IC BA1404 from ROHM Semiconductors. BA1404 is a monolithic FM stereo modulator that has built in stereo modulator, FM modulator and RF amplifier. The FM modulator can be.... -
The circuit is based on the IC BA1404 from ROHM Semiconductors. BA1404 is a monolithic FM stereo modulator that has built in stereo modulator, FM modulator, RF amplifier circuitry. BA1404 FM transmitter can be operated from 76 to 108MHz and power supply for.... -
LA4440 is a dual channel audio amplifier IC. It can be used in two modes one is Stereo amplifier and another Bridge amplifier mode. The LA4440 is a monolithic linear IC from Sanyo. Here I give the both circuit mode of amplifier using IC LA4440. C10 is filter.... -
an FM modulator that modulate a carrier frequency with the composite signal, and an RF amplifier that provide enough power to be transmitted through antenna. Here is the schematic diagram of theFM transmitter circuit: The core of this stereo FM tra.... -
BA5417 is a stereo amplifier IC with a lot of good features like thermal shut down, standby function, soft clipping, wide operating voltage range etc. The IC can deliver 5W per channel into 4 ohm loud speakers at 12V DC supply voltage. The BA5417 has.... -
A Left and Right source of audio are first pre-emphasized (HPF) and then fed to adder circuits. The output of one adder is the sum of the two signals, or the L + R signal (the monaural signal), and the output of the other adder is the difference of the two.... -
This design was born of frustration with the mic preamp in my Sony R91. It clips at ridiculously low levels, basically it has 28mV of headroom to deal with an input that could be as high as 1800mV (depending on mic & volume), so this design attempts to cure.... -
This circuit senses AC audio voltage supplied to the car-radio loudspeakers and displays it as power using a LED bar graph, achieving at the same time an attractive visual effect. It is designed to cover common car-radio output power ranges, but can easily.... -
On the amplifier circuit using ic STK, the same as my previous posting. However, in the above circuit has 2 inputs and 2 outputs, or commonly called a stereo amplifier. This issue of power amplifier 2 x 18Watt and has impedance 8. To stress that it takes.... -
The circuit shown here is a simple stereo FM transmitter that can transmit signals of high quality with a range of 70 feet. The circuit is based on BH1417 PLL Stereo Transmitter IC semiconductor Rhom. The IC has separate sections of audio processing for the.... -
Car Stereo Amplifier Circuit with TDA2040 is shown here. TDA2040 is a monolithic integrated audio amplifier operating in Class AB mode. The IC has built in short circuit protection circuitry and thermal very close and more about it can be operated from a.... -
This circuit has accouterment for abutting stereo outputs from four altered sources/channels as inputs and alone one of them is selected/connected to the achievement at any one time. When ability accumulation is angry on`, approach A (AR and AL) is selected..... -
This stereo balance indicator circuit diagram is designed using few common external components. The schematic circuit is very simple to build and will provide an visual indication with LEDs for left, right and center balance. Outputs from each channel are....
Neighbour Categories
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Soundblaster soundcard series (SB16, SB32, AWE32 and AWE64) have all a microphone input designed...
The circuit tests whether or not a diode is open, shorted, or functioning correctly. If lamp A...
The cell phone shield circuit uses two NE555 timer ICs: One as being a very simple astable...
TL072 a low noise JFET input operational amplifier with features such as common-mode input...
The circuit below is similar to designs using unijunction transistors to generate the triggering...
As shown in the following figure is double coil metal detector circuit. The probe by the probe,...
Audio AGC can keep track, monitor audio preamplifier output signal level when the input signal...