After the 2-way active loudspeaker circuit, give a complete electronic section circuit of one 3-way active loudspeaker. The speaker?s choice will become from you, because the particular circuit has the driving possibility all almost trade loudspeakers. The choice that made in the crossover stage, is a 3-way crossover [Butterworth] with cut off -point frequencies 200HZ and 3500HZ, with slope -12dB/oct. These frequencies can change and adapted in your own speaker?s choice, using the calculation types of Fig.5. Exist the possibility is used other circuit crossover, as the circuit of 3-way active crossover with slope -24dB/oct. The circuit crossover does not exist above in main PCB, but is contact with this via the plug J2A that is applied above in the J2B.
Click here to download the full size of the above Circuit.
Click here to download the full size of the above Image.
This can become if in the place of J2A it?s placed a pinhead with 8 pin and PCB crossover put on above main PCB in form sandwich. It can however be placed in other point and with a flat cable to transport the signals and the voltages from J2A in the J2B. Power supply for ± 15V of the crossover circuits it?s found in main PCB. A point that I want to highlight is with regard to various in the calculation values precision and real values of resistors and capacitors. It?s good, if the component value does not exist in standard value to select a combination that us will give value near in theoretical and simultaneously to do the same and in the other loudspeaker, in order that the divergence is same. In the drawing exist parallel combinations resistors, and somebody?s from these are not used if they do not need. With the TR1-2 we adjust the level of high and mid speakers, if it needs.
Part List [Fig.1]
R1=47Kohms R19-20=47ohms C17-18=47uF 25V
R2=1Kohms C1=2.2uF 63V MKT TR1-2=47Kohms trimmer
R3=4.7Kohms C2=220pF IC1=TL071
R4-11-13-15-17=NC C3-4-11-12=100nF 63V MKT IC2-3=TL072-NE5532
R5-6=12Kohms C5-6-9-10=10nF 63V MKT J1=2pin conn. 2.54mm pin step
R7-8=120Kohms C13=6.8nF 63V MKT J2A=8pin conn. 2.54mm pin step
R9-10=220Kohms C14=3.3nF 63V MKT or 8 pinhead 2.54mm pin step*
R12-14=10Kohms C15=33nF 63V MKT
R6-18=33Kohms C16=18nF 63V MKT All Resistors is 1/4W 1%
Typical specifications
Input sensitivity
1Vrms...
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of....
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is....
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to....
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This....
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the....
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,....
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the....
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power....
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
characters left: