Mosfet amplifier schematic 25 Watt


Posted on Sep 2, 2012

Can be directly connected to CD players, tuners and tape recorders. Simply add a 10K Log potentiometer (dual gang for stereo) and a switch to cope with the various sources you need. Q6 & Q7 must have a small U-shaped heatsink. Q8 & Q9 must be mounted on heatsink. Adjust R11 to set quiescent current at 100mA (best measured with an Avo-meter in series with Q8 Drain) with no input signal. A correct grounding is very important to eliminate hum and ground loops. Connect in the same point the ground sides of R1, R4, R9, C3 to C8. Connect C11 at output ground. Then connect separately the input and output grounds at power supply ground.


Mosfet amplifier schematic 25 Watt
Click here to download the full size of the above Circuit.
Mosfet amplifier schematic 25 Watt  - image 1
Click here to download the full size of the above Image.

Technical data: Output power: well in excess of 25Watt RMS @ 8 Ohm (1KHz sinewave). Sensitivity: 200mV input for 25W output. Frequency response: 30Hz to 20KHz -1dB. Total harmonic distortion @ 1KHz: 0.1W 0.014% 1W 0.006% 10W 0.006% 20W 0.007% 25W 0.01%. Total harmonic distortion @10KHz: 0.1W 0.024% 1W 0.016% 10W 0.02% 20W 0.045% 25W 0.07%. R1,R4 = 47K 1/4W Resistors R2 = 4K7 1/4W Resistors R3 = 1K5 1/4W Resistors R5 = 390R 1/4W Resistors R6 = 470R 1/4W Resistors R7 = 33K 1/4W Resistors R8 = 150K 1/4W Resistors R9 = 15K 1/4W Resistors R10 = 27R 1/4W Resistors R11 = 500R 1/2W Trimmer Cermet R12,R13,R16 = 10R 1/4W Resistors R14,R15 = 220R 1/4W Resistors R17 = 8R2 2W Resistor R18 = R22 4W Resistor (wirewound) C1 = 470nF 63V Polyester Capacitor C2 = 330pF 63V Polystyrene Capacitor C3,C5 = 470µF 63V Electrolytic Capacitors C4,C6,C8,C11 = 100nF 63V Polyester Capacitors C7 = 100µF 25V Electrolytic Capacitor C9 = 10pF 63V Polystyrene Capacitor C10 = 1µF 63V Polyester Capacitor Q1-Q5 = BC560C 45V100mA Low noise High gain PNP Transistors Q6 = BD140 80V 1.5A PNP Transistor Q7 = BD139 80V 1.5A NPN Transistor Q8 = IRF532 100V 12A N-Channel Hexfet Transistor Q9 = IRF9532 100V 10A P-Channel Hexfet Transistor R1 = 3K3 1/2W Resistor C1 = 10nF 1000V Polyester Capacitor C2,C3 = 4700µF 50V Electrolytic Capacitors C4,C5 = 100nF 63V Polyester Capacitors D1 200V 8A Diode...




Leave Comment

characters left:

New Circuits

.

 


Popular Circuits

BFO Circuit
High Speed NiCd Charger for R/C
Programmable Timer For Long Intervals
HV SUPPLY METERING & OVERVOLTAGE TRIP
GSM Remote Control 2 IN and 2 OUT Part 2 Schematic
Dual flashing string circuit 2
You can set 1 10 100 1000 times magnification programmable amplifier



Top