Designed around an LM3900 quad op amp, this mixer combines 2-line and 2-mike inputs and sums them at the output terminal. ..
Four (or more) inputs can be mixed and produce stereo output. Gain of each stage can be boosted by adding RX, but it should be kept below 50 (RX above 2 K) to avoid poor frequency, response. If more than four stages are used, decrease RXto 6 K for six inputs, or 4 K for eight inputs..
This simple circuit can be used to combine stereo signals to produce a monaural output..
This circuit can be used as a mixer and a stereo track four. The quad op-RNAP IC gives a little gain for each track, the pan control provides panning between one and two tracks with the switch to high, and with the switch to low, it is possible to pan between the tracks and three four channels can be added. ..
This stereo mixer has two mono mixers and a modification to the microphone inputs. When a microphone is in u..
High gain op amp combines up to four individually controlled input signals..
This mixer is built around a TL072 dual BiFET op amp with a JFET input stage, and can be powered from a single-ended 9-to 18-V power supply. The microphone input is capacitively coupled to the noninverting input of U1a. Resistors R1 and R3 set the voltage gain at about 26 dB and serve as a negative feedback network for U1a. Capacitors C1 through C3 are de-blocking capacitors. Most high-impedance microphones have outputs of a few mV. ..
Using two op amps, this circuit produces a full-wave rectified version of the input signal. Op amp IC1 invert..
CMOS switches are used directly to select the entries in the audio circuits, it can introduce unacceptable levels of distortion, but if the switch is included in the feedback network of an op amp, the distortion due to the switch may be virtually eliminated. The circuit uses a CMOS switch 4416, arranged as two independent SPDT switches. If switching transients are unimportant, R5 and C1 can be omitted, and R4 may be short-circuited. ..
This circuit illustrates some possible buffer combinations. Tbese include a differential input stage, a voltage follower as well as both noninverting and inverting stages. The allowable resistor ratios and recommended device types are also included. One restriction applies to this type of mixernetwork in which Rg is greater than 2.4 KO. ..
By inserting a high-pass filter section in the IF lead, this mixer is terminated at all frequencies, besides the IF, for oth..
If you want to do the ground loop elimination in audio path, you have to cut the galvanic connection but pass the whole audio range. The simplest and most common way to do the isolation is use audio transformer which is ment for audio use. Transformers for audio use have some problems like distorted bass response and attenuating in high-frequency response. Basically a transformer slows down upper frequencies and allow the low frequencies to pass first, creating what we.....
That circuit will provide an overall gain of one between the output and each input channel. Each input channel includes a single 0.1uf capacitor and 100-Kilohms resistor to provide an output impedance of 100K. The number of input channels to this audio mixer can be increased by adding more capacitors and resistors with same value as capacitor(0.1uf) and resistor(100K). The mixer should be located between the output of tone control circuitry and the input to the power.....
This is an image Schematic. No Description available...
The mixer is the common "virtual earth" mixing amplifier, and there is nothing special about it. Note that it is inverting, which complements the tone controls (also inverting) so the absolute signal polarity is maintained. As shown, the mixer also has a gain of a little over two times, and again this can easily be changed. Making R115/215 10k sets the gain at -1 (i.e. unity, but inverted). Note that R117/217 are not mounted on the board, but mount directly on the output.....
This simple circuit mixes two or more channels into one channel (eg. stereo into mono). The circuit can mix as many or as few channels as you like and consumes very little power. The mixer is shown with two inputs, but you can add as many as you want by just duplicating the "sections" which are clearly visible on the schematic...
The circuit is designed to work with typical HIFI amplifiers where negative speaker connector (black) is connected to amplifier ground. Be careful here because some modern amps have both terminals actively driven. Connecting either one to a common reference could cause the output stage to smoke...
This is a classic signal mixer that is used for audio purpose. VR1 & VR2 are inputs audio volume controlers and VR3 is used to control the balance between Input1 and Input2. connect a dynamic microphone to Input1 and a music without vocal to Input2, then adjust the VR1, VR2 and VR3 for obtaining a good mixed audio signal from the circuit Output. VR4 is an optional volume control for output audio signal. ..
The circuit is suitable to be uses as a mixer between two line level sources and one HIFI amplifier input. This circuit have been successfully used for mixing signals form two CD players or computer soundcard and CD players. There are many situations where simple mixer would be useful and commercially available mixer desks are too expensive and big...
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
