Electronic Circuits Schematics Projects




Tubed Crossovers

Rating: 8.00/10 (81Votes cast)

Category: Audio Circuits / Tone Balance
Views: 4319
Rank: 0

You'll find here few ASCII schematics for Heath and Marantz tube crossovers. They were given in L'Audiophile No 11 old sery July 1979. In the same paper there is another tube crossover designed by Gerard Chretien now at the head of Focal i'll try to send an ASCII schematics of that one tomorrow. Here is an ASCII schematic for the Bessel crossover (2nd and 4th orders) designed by Larsen and Chretien. visit page.

Related circuits

Tiny 1MHz Lowpass Filter Uses No Inductors

The LTC®1560-1 is a fully integrated continuous-time filter in an SO-8 package. It provides a 5-pole elliptic response with a pin selectable cutoff frequency (fC) of 1MHz or 500kHz. Several features distinguish the LTC1560-1 from other commercially available high frequency, continuoustime...



Closing the loop deepens notches

Notch filters remove a single unwanted frequency from an input signal. They are also a vital component of pulse-shaping networks, such as time-averaging filters. You can tune a state-variable filter over a wide range by changing the time constants of its integrating amplifiers (References 1, 2,...



3KHz LOW PASS FILTER & AUDIO AMP

This is an image Schematic. No Description available.



TONE CONTROL AND SUBWOOFER OUT

PT2350 is a tone control subwoofer cross-over low pass filter chip utilizing CMOS Technology. It features a tone control range of + 10dB (50Hz, 4 KHz) and subwoofer low pass filter of the second order Sallen Key Design. The roll-off point can be adjusted by changing the value of the external...



12dB / Octave Linkwitz Riley Crossover

The circuit diagram of the filter section is shown in Figure 1. It is a completely conventional filter, and the component designations are the same as for the 24dB unit described in Project 09. It is designed primarily for 2-way electronically crossed over systems, such as adding a subwoofer or...



Auto Loudness Control

Simple add-on module. A simple approach to this problem can be done inserting a circuit in the preamplifier stage, capable of varying automatically the frequency response of the entire audio chain in respect to the position of the control knob, in order to keep ideal listening conditions under...



Guitar treble boost

Ql is connected as an emitter follower in order to present a high input impedance to the guitar. C2, being a relatively low capacitance, cuts out most of the bass, and C3 with RV1 acts as a simple tone control to cut the treble, and hence the amount of treble boost can be altered.



Schematic of Low-Pass Active Filter

This is an image Schematic. No Description available.



Articles & Projects
Older tube amplifiers only utilized class A circuits. Class A circuits do not exhibit the crossover distortion found in A/B and B topologies and therefore are considered more musical and pleasing to the ear. This lack of crossover ...

This is Thomas Mayer's blog about vacuum tube audio. Concepts, ideas, unusual circuits and tubes, directly heated triodes, LCR RIAA EQ. Circuits with favorite tubes: EC8020, E55L, D3a, 851, 849, 845, 841, 801A, 866A, 211 ...

Anyone built or heard a tube crossover in use? I guess I'd just love to have a tube crossover. These could sound awesome in ... Crossover circuits (as "I" know them) are passive devices. Active devives would constitute ...

I wanted to split some of the discussion off from the Pete Millett crossover PCB thread, but figured it would be easier to start a new one. Whereas... ... Here's the options: this will be a second-order circuit. Most likely to get done ... If people want the bass to be done with tubes and/or a th...

Low power tube amp using 6P14A amplifier more and more attention. One reason for the CPI amplifier crossover distortion does not ...Sample and Hold Amplifier AD9100 high-speed track-hold amplifier circuitAD9100 is a monolithic sample ...

A screen voltage regulator and DC restoration circuit minimizes crossover distortion and output tube power dissipation. The 1.5 ohm output impedence coupled with current and voltage feedback loops also allow the amplifier ...

last crossover circuit replicatiion mod

Passive low pass RL filters


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits