Remote Control Circuits
- Page 6
-
This circuit is which enables switching on` and off` of appliances through telephone lines. It can be used to switch appliances from any distance, overcoming the limited range of infrared and radio remote controls. The circuit described here can be used to....
-
-
-
How to turn on equipment by sending SMS `1111` ON `and switch off the equipment by sending SMS` 0000 GSM Switch will receive instructions either load 1 (L1), load 2 (L2), load 3 (L3) or load 4 (L4). Then the GSM Switch will send the four load status is ONor....
-
To send the Sony command "TV - mute", the command would be infraout 1, 20. Note that device should always be 1 when used in PICAXE projects and data can only be between 0 and 127, as the SIRCS protocol only specifies 7-bit capability. The full program for....
-
This is Infrared Remote control transmitter circuit has high performance and can be applied to works with the various infrared receiver circuit. To made easily. And best to save your money. - Then another circuits, is designed to have wider applications. Can....
-
The build makes use of a 10 x 20 grid of RGB LEDs controlled by the myRIO. It`s played by using a web interface on any device, as long as you have WebSockets support. [Sam] had originally built it using an Arduino at the heart, but wanted a stand-alone....
-
-
Electronics Nerd shows us how to reverse engineer an IR remote control signal. By understanding what type of signal is being transmitted out of the remote control allows a microcontroller to simulate the code to control the Hampton Bay Air Conditioner. "In....
-
An infrared remote control tester circuit that can be made without spenting much money. This IR tester build around an infrared reciever module TSOP1738. We can observe the remote control state by listening to the buzzer sound. The circuit is very sensitive....
-
This is the most popular IR Remote control circuit for home appliances like lamp, fan, radio, tv etc to make the appliance turn on/off from a TV, VCD or DVD remote control. It is very simple to build because of few components and simple design. The circuit....
-
Here we explain a couple RF 433kHz remote control chips especially designed for the purpose. The IC TWS-434 along with its encoder chip HOLTEK`s HT-12E form ahigh class transmitter circuit, whereas the chip RWS-434 through its complementing decoder IC HT-12D....
-
The proposed remote control circuit idea can be used for controlling any electrical gadget within a range of 100 meters. Since the idea here is to modify an existing circuit of a remote bell unit, becomes super easy without any complications. However the....
-
-
Nikon infrared remote control with some special features interval shots, multiples shots, continuous shots....
-
Simple circuit diagram is a schematic remote control, remote control where it consists of two parts of the transmitter and receiver. The first part is a transmitter, circuit diagrams for transmitter IC is controlled by the NE555. This system works by....
-
At certain times of the year I migrate a bit North of Southampton to an area where the the hams on VHF are grumbly and seem to be few and far between. Add to this that the local repeater only uses tone burst and that the QTH is right next to some noisy....
-
-
As more than one switches are to be controlled, we have to transmit a number of bits through IR transmission to indicate which is key is pressed on the remote and accordingly which switch of the switch-board to control. In this project, this is done by using....
-
You can control any electrical gadget from any part of the world through your cell phone, that too without spending a penny for the individual commands. Whether it`s you vehicle, your basement door, your mansion gate or simply the air conditioner of your....
-
The Tiny Remoteis a very compact infrared remote control with only two buttons to control an iRobot Roomba. It produces three different infrare....
-
-
-
Remote controls are part of an electronics device used for operating the device remotely. Remote control has continuously evolved and advanced over recent years. The technologies likebluetoothconnectivity, motion sensor enabled capabilities and voice control....
-
A circuit of a remote control unit which makes use of the radio frequency signals to control various electrical appliances. This remote control unit has 4 channels which can be easily extended to 12. This circuit differs from similar circuits in view of its....
-
This is a simple type remote control by using RF communication without microcontroller. In this project a remote has been designed for various home appliances like television, fan, lights, etc. It gives lot of comfort to the user since we can operate it by....
-
The circuit is a remotely operated DTMF telephone. The circuit can be used to change up to 9 devices using the keys 0 to 9 phone. Digit 0 is used to switch between the phone system remotely and change the way of normal conversation. IC KT3170 (DTMF to BCD....
-
-
-
-
Decoder Tags: PT2262, PT2272, Remote Control, RF-RX-315, RF-TX-315 Remote Control 315MHz by using RF remote control Encoder and Decoder Published by: cl.chin on September 3, 2012. 48 Share Tweet 3 Share Share Introduction RF-TX-315 & RF-RX-315 RF Modules....
-
The latest addition to my collection of Infra Red (IR) Repeater circuits. The Mark 5 is a much improved version of the Mark 1 circuit and has increased range and sensitivity. It is also immune to the effects ofambient light, daylight and other forms of....
-
This circuit confuses the infra-red receiver in a TV. It produces a constant signal that interferes with the signal from a remote control and prevents the TV detecting a channel-change or any other command. This allows you to watch your own program without....
-
-
This project is based on integrated circuit from Holtek Semiconductor HT6221/HT6222. Similar parts used to be produced by NEC Semiconductor uPD6121/uPD6122. These ICs are commonly used in television and VCR infra red remote controls, garage door controllers,....