Car Bike Circuits
- Page 9-
This circuit also prevents the shutdown circuit of the IR2161 from operating in the normal way and therefore the external SCR based protection circuit also needs to be added. .. -
As a wideband PLL FM Demodulator the UTC L2572 is intended for application in satellite Tuners primarily. The device includes all the necessary elements, with external Oscillator sustaining network and the exception of loop feedback components, to form a PLL.... -
The LA3401 is an MPX IC for FM car stereo use. It con- tains the VCO non-adjusting function, skip noise eliminat- ing function, and pilot cancel function and is packaged in a 16-pin SIP. By Sanyo Semiconductor Corporation .. -
The LA4165M Recording-Playback IC combines the functions required to design the recording and playback systems and Motor Control circuits for micro- or standard-cassette tape recorders into a single chip. Functions provided include Automatic Audio input.... -
The TDA8340 Q and TDA8341 Q are integrated IF Amplifier and Demodulator circuits for colour or black/white Television receivers, the TDA8340 Q is for application with n-p-n Tuners and the TDA8341 Q for p-n-p Tuners The TDA8340 Q and TDA8341 Q are.... -
A diagram of an active loudspeaker. The LF353 of, National Semiconductor, is going to split audio signal into three bands. SANYO LA47536 is going to amplify these signals. In stereo mode, we shall have the action of eight high speakers who are going to.... -
This circuit has been designed to provide a clearly visible light, formed by 13 high efficiency flashing LEDs arranged in a pseudo-rotating order. Due to low voltage, low drain battery operation and small size, the device is suitable for mounting on bicycles.... -
This circuit uses the popular and easy to find LM3914 IC. This IC is very simple to drive, needs no voltage regulators (it has a built in voltage regulator) and can be powered from almost every source. Electronics project.... -
Most of the time a charged lead-acid battery and a power inverter would be used to ensure a smoothly organised holiday where ideally the missus and the children cheerfully use their electric and electronic gear! With rechargeable lead-acid batteries it`s.... -
The past experiences was pretty difficult, because the car horns have an inductive charge and it takes 12A and peak may be at 20 or 30A. The current electronic system is not reliable at all. It`s a lot of intensity. I need to dissipate 240W => 0. 3 x 240 =.... -
Unlike many units, this battery charger continuously charges at maximum current, tapering off only near full battery voltage. In this unit, the full load.... -
22W into 4 Ohm power amplifier, Variable Low Pass Frequency: 70 150Hz This unit is intended to be connected to an existing car stereo amplifier, adding.... -
The ASUS Eee is a fantastic ultra-portable notebook with almost everything required for geeks (and nothing that isn t). Plus it features fantastic build q.... -
A useful timing strobe can be constructed using high-brightness LEDs and a few common components. Ignition pulses from the number 1 cylinder high-tension lead are used to trigger the circuit via a home-made inductive pickup. Transistors Q1 & Q2 buffer and.... -
This circuit has been designed to provide a clearly visible light, formed by 13 high efficiency flashing LEDs arranged in a pseudo-rotating order. Due to low voltage, low drain battery operation and small size, the device is suitable for mounting on bicycles.... -
This simple circuit allows a 12V battery pack to be charged via a bike generator. The generator is rated at 3W and with this voltage multiplier circuit pr.... -
Going camping nowadays involves taking lots of electronic equipment whether for day to day running or for fun and entertainment. Most of the time a charge.... -
A car battery deteriorates in use and its life seldom exceeds four years. When new, its voltage may drop to only 2V while cranking the engine. As the batt.... -
Most cars do not have delayed interior lights. The circuit presented can put this right. It switches the interior lights of a car on and off gradually. Th.... -
Here is a simple circuit that starts playing the car horn whenever your car is in reverse gear. The circuit (1) employs dual timer NE556 to generate the s.... -
This digital DIY tachometer for bikes uses two reed switches to get the speed information of the bicycle. The reed switches are installed near the rim of.... -
An interesting circuit of a bicycle horn based on a popular, low cost telecom ringer chip is described here. This circuit can be powered using the bicycle dynamo supply and does not require batteries, which need to be replaced frequently. The section.... -
To operate car audio (or video) system from household 230V AC mains supply, you need a DC adaptor. DC adapters available in the market are generally costl.... -
This add-on circuit enables remote switching on/off of battery-operated toy cars with the help of a TV/video remote control handset operating at 3040 kHz.... -
First I bought another front wheel, one which has a dynamo already built in the hub. This supplied a nice sine wave of 30 Vpp (at no load). With this knowledge I designed a simple power supply. The transistors that are used are type BD911. These are a bit of.... -
This circuit automatically turns a motor cycle`s headlight on and off, independently of both the light and ignition switches, provided the battery is fully charged. The first stage uses the 22O resistor and ZD1 to hold transistor Q1 off while the motor is.... -
For Check battery in car, It use IC CA3140 and Transistor, Easy circuit. For electricity pressure of automobile battery is important many factor. If be high.... -
This subwoofer filter set Suitable for use with a great car audio system. Since this circuit is designed to operate with a 12 volt DC power. But if you.... -
I used a main part and 2N3055 Transister and IC TL072 for pulse oscillator generator. The output have voltage +50V and -50V at 2A to 3A. You must is used this.... -
This circuit is the sound generator super siren, for use be alarm signal get by live frequency generator circuit that use, op-amp circuit. The principle works to are while still no press switch S1 will still have no the loud sound comes out from a....
Neighbour Categories
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
In the form it appears the theoretical circuit of filter. In first glance we see three different...
Sensing circuit detects either steady or fluctuating air flows. The heart of the circuit is a...
This Car LED Light Sequencer uses a standard 74C164 8 bit shift register as its heart of...
TDA1072AT is a special purpose integrated circuit for AM radio receiver from Philips...
Since you say that with my PWM circuit the current consumption of the inverter shoots to a...
The LM35 of National Semiconductors that is used in this project is a precision centigrade...
This level liquid sensor electronic circuit diagram is based on a common Ca3410 operational...
A dancing light can be easily constructed using a 555 timer wired in astable mode. Please read...
A cheap garland tree and fill it full of blinking LEDs. The tree shown is a cheap garland wrapped...
All components that used in Moving Sensor / Detector Schematic Diagram using IC NE555 and...
This display uses ten LED`s to display a voltage range from 10. 5 to 15 volts. Each LED...
Boil water or cook with gas stove, it is sometimes due to water spills extinguish the fire...