MSF detector - turning the radio signal into data

Posted on Feb 5, 2014

The MSF transmitter sends time data bit-by-bit over the 60 seconds of each minute by dropping the 60 kHz carrier. It`s a basic CW signal [1]. Two bits are transmitted every second by modifying the length and number of carrier drop(s) per second (see the second article in this series). As is often the case in timing circuits a negative logic is use

MSF detector - turning the radio signal into data

Click here to download the full size of the above Circuit.

d. When the carrier is ON the data being sent is a `zero` and when the carrier off it is a `one`. It is the drop in career that is accurately timed i. e. the ON to OFF state rather than the OFF to ON state. I suppose dropping the carrier (ON to OFF) is a clearer transition than the OFF to ON transition, as fading might confuse the exact ON transition but the carrier going fully OFF is quite distinct. Reading the data sheet from the NPL it appears that they do more than key the carrier ON and OFF to get the precise signalling. This may be because the high Q antenna / output circuit will `ring` for too long after the transmitter keys off. They imply that the ON / OFF data is a combination of data pulse and actual switching of power to the antenna system [1]. In principle we can take the changing voltage from the receivers automatic gain control (AGC) i. e. the S-meter circuit as the basis of the data detection signal. The S-meter voltage can be feed into a comparator / trigger to convert the change in signal strength into logic level (0 and 5V) data pulses. If the MSF signal is very steady and strong (i. e. if you are relatively near to the transmitter) then this will work well. This is shown at the top of the first picture. A little bit of hysteresis built into the comparator circuit will help to stop `chattering` at the transition edges at switch ON and at switch OFF. The main problem is when the signal strength is weak or...

Visit page

Leave Comment

characters left:

Related Circuits

Simple Discrete Logic Probe

This is simple logic probe circuit. Logic probe is used to determine if a point in a circuit has high or low state when the circuit is in operation.? Here is.

Simple Electronic Combination Lock circuit diagram

This could be the circuit diagram of a easy electronic combination lock by using IC LS 7220. This circuit may be applied to activate a relay for controlling (on & off) any device each time a preset...

Simple FM Transmitter Circuit

Simple FM Transmitter Circuit This simple FM transmitter circuit was built using a transistor with a transmission distance of about 300m around your home. It`s.

Simple Function Generator Circuit

Here is simple function generator. Built around a single 8038 waveform generator IC, this circuit produces sine, square or triangle waves from 20Hz to 200kHz in.

Simple Fuse Monitor Indicators

This is a circuit diagram fuse monitor circuit indicators. This very simple circuit uses only two components, but only with a single resistor and LED this circuit provides visual indication when...

Simple High Impedance DC Voltmeter Using a uA741 Op-amp

Circuit diagram of this simple in design for high voltage DC Impedance. This is a circuit diagram with circuit design that was built by uA741 IC. IC is the op-amp non-inverting DC amplifier. IC...

Simple Humidity Sensor

You can use a humidity sensor to give an alert of boat leakage, or when your books start being flooded by heavy rain attack on your broken roof, or anything you.

Simple Intercom Circuit Transistor

Circuit diagram is a simple but effective circuit intercom circuit is based entirely on transistors. Circuit diagram is based on three stages plus RC amplifier. When the pushbutton S2 is pressed,...

New Circuits

Zero consumption Anti-theft High power Code Switch for E-Bike Batteries

This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of....
Ultrasonic distance finder circuit

The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is....
Simple Metal detector circuit with CD4030

Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to....
Fully automatic watering circuit for flower pots

Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This....
Simple deep searching metal detector circuit

The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the....
Sub-Harmonic Bass Converter for Electric Guitars

The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,....
Echo Depth Sounding Sonar for Boats

In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the....
100W HiFi Audio Amplifier Circuit

This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power....
Plant-Pot Water Level Indicator Circuit

A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....

Create NOW your QR MENU for your Restaurant / Hotel / Bar / Caffe,

Comprehensive ordering/paying features. fully personalized to suit your Business.

Update Anytime! Easy and Simple!

Popular Circuits

LM1800 Stereo Demodulator

Build your own Accurate LC Meter (Capacitance Inductance Meter) and start making your own coils...

famicom disk system fd3206 write mod

Install your fresh mod board into your FDS drive mechanism. You need to cut two traces and solder...

555 timer mono stable one shot circuit

The two circuits beneath allegorize application the 555 timer to abutting a broadcast for a...

Dual power supply using L165

This dual power supply is based on the L165 power operational amplifier from SGS-Thomson Micro...

IR Widget Consumer infrared remote control capture and visualization

The IR Widget operates in a way that makes it compatible with modern multitasking operating...

YD7312 DUAL RECORDING/PLAYBACK PREAMPLIFIER CIRCUIT WITH ALC

The YD9088 is a bipolar integrated circuit for use in mono portable and pocket Radios It is used...

Electromagnetic Field Probe with Meter Outputs

This tester is designed to locate stray electromagnetic (EM) fields. It will easily detect both...

Easy Auto power battery charging circuit

Easy Auto power battery charging circuit Is shown as a simple automatic power battery charging...