Repository-circuits
- Page 594
-
FSK or Frequency-Shift Keying is a form of frequency modulation in which the modulating signal shifts the output freq. between predetermined values. If problems arise in demodulating FSK signals, it is helpful to use the FSK filter circuit....
-
-
The transmitter offers a optical link (infrared) for headphones. Three infrared leds (ir) are polirised by T1 current, P1 is used to adjust the current level. Current consumption of this headphones infrared transmitter is about 60mA at 9V....
-
You probably know that LM317 IC is used as an adjustable voltage regulator, but did you know it can be used as an audio amplifier? This is a class A audio amplifier built with LM317 that delivers a maximum 1W audio power. Use a good heatsin....
-
Here the simple mixer with 4 input and 2 op-amps: A basic mixer suitable for mixing microphones or even effects outputs. The overall gain from input to output is one if the pot related towards the input is full up. You can make this a net g....
-
Zetex Semiconductors have a siren driver IC Type ZSD100 available that is suitable for use in alarm systems for cars and model craft. With the addition of only a few components as shown in the diagram, the device produces an ear-splitting s Zetex....
-
This is a stereo VU booster circuit diagram based on transistor FCS9014 which usually used for pre-amp and regulator circuit. This circuit should be connected to audio channel before amplifier module. If you are using tone control or equali....
-
-
This stereo amplifier is for car purpouse and can deliver up to 2 x 22W using a single TDA1557Q or TDA1553Q from Philips. TDA1557Q TDA1553Q datasheet More audio car amplifier circuits....
-
TDA 2030 audio amplifier can output 20 W but in this schematic we have reduced the power to 8w and we use 10w speakers. The input sensivity is around 200mV and the amplifier is set by the 47k and 1.5k resistors. TDA2030 amplifier circuit di....
-
Join the forum discussion on this post This is a simple home telephone ringtone generator circuit which is built with applying only several electronic components / parts. It generates simulated telephone ringtone and requires only DC supply....
-
This is the circuit diagram of UHF band TV antenna booster with 15dB gain power. This low cost antenna booster is simple and easy to build. This circuit formed based on BF180 UHF Transistor. The first stage is an band pass filter constructe....
-
This dc voltage doubler circuit produces a voltage that is twice its voltage supply. This is useful when a higher voltage level is needed out of a single lower voltage power supply. Since the current consumption levels are low in such cases....
-
-
Automatic Headlight Brightness Switch Circuit Driving the highway with your high-beam headlights can really increase your visibility, but can he a blinding hazard for other drivers. This simple circuit can be wired into your hea....
-
Automobile Interior Lights Fader Circuit diagram Circuit This circuit is similar to the fading eyes circuit above and is used to slowly brighten and fade interior lights of older cars. The circuit is based around the LM324 low p....
-
Battery Indicator Circuit For The Caravan Circuit This i-TRIXX circuit can prevent a whole lot of trouble for those of you who go on holiday in a caravan. It would be a significant damper on your holiday spirit when you are read....
-
The following diagram is the schematic diagram fo Car Horn, you may try this circuit for your car modification Components List: R1 = 68K R2 = 2K2 R3 = 56K R4 = 3K3 R5,R6 = 4K7 R7 = 10K Pot/trimpot C1,C2 = 22nF C3,C5 = 100nF C4 = 1nF C6 = 22....
-
Park Aid Three LEDs signal bumper-barrier distance Infra-red operation, indoor use Circuit diagram: Parts: R1 10K 1/4W Resistor R2,R5,R6,R9 1K 1/4W Resistors R3 33R 1/4W Resistor R4,R11 1M 1/4W Resistors R7 4K7 1/4W Resistor R8 1K5 1/4W Res....
-
Car and Motorcycle Battery Tester Circuit Going camping nowadays involves taking lots of electronic equipment whether for day to day running or for fun and entertainment. Most of the time a charged lead acid battery and a power....
-
Economy radar detector Circuit diagram This circuit uses a 1458 dual op-amp to form a radar detector. C1 is the detector of the radar signal. The first op-amp forms a current-to-voltage converter and the second op-amp buffers the output to....
-
LED 12 Volt Lead Acid Battery Meter Circuit In the circuit below, a quad voltage comparator (LM339) is used as a simple bar graph meter to indicate the charge condition of a 12 volt, lead acid battery. A 5 volt reference voltage....
-
Motor Bike Headlight Controller Circuit Circuit This circuit automatically turns a motor cycle`s headlight on and off, independently of both the light and ignition switches, provided the battery is fully charged. The first stage....
-
Simple but reliable car battery tester Circuit diagram This circuit uses the popular and easy to find LM3914 IC. This IC is very simple to drive, needs no voltage regulators (it has a built in voltage regulator) and can be powered from almo....
-
Speed-limit Alert Wireless portable unit Adaptable with most internal combustion engine vehicles Circuit diagram Parts: R1,R2,R19 1K 1/4W Resistors R3-R6,R13,R17 100K 1/4W Resistors R7,R15 1M 1/4W Resistors R8 50K 1/2W Trimmer Cermet R9 470....
-
Here the circuit diagram of simple and easy made battery level indicator. In general, in mobile phones, the battery levels is displayed in dot or bar style. This helps you to effortlessly acknowledge the battery level. On this page we provi....
-
This USB car charger circuit adapter from car cigar socket project is a DC DC power converter that safely converts the 12V car battery voltage into stable 5V. This circuit can be used to supply power from a car cigar lighter socket to a por....
-
This circuit is used to simulate the police car lights by alternating flashing strobes seen on British police cars. The IC1a forms a square wave oscillator having adjustable frequency with VR1 to give the best effect. This square wave is bu....
-
AC mains operated single LED flasher circuit, built using the popular CMOS timer chip TLC555 is shown below. The whole circuit is powered directly by the grid supply of 230VAC through a capacitive potential divider and associated components....
-
Here is an ultra simple automatic light switch circuit for bedrooms. After construction,connect the input terminals of this circuit in parallel to the internal buzzer terminals of a Quartz-Alarm Clock. When the clock alarm is activated at a....
-
This is a simple update to Mr. Hareendran s PIR Sensor Security Light circuit. It has a shortcoming limits the relay voltage to approximately 3.3V. While this may function with some 5V relays, it will not function with all. The nature of....
-
Using this simple circuit, you can make an 18 LED flasher to decorate the X`Mas Tree. The White, Blue and Red LEDs flash at different rates to give a colorful display. It is a light sensitive circuit so that it will turn on in the evening Using this simple....
-
This diagram is certainly the 6 transistor Tilden H-bridge circuit; while not as old as the original basic H-bridge, this goes way back, and will be the basis for a lot of BEAM driver circuits. Bruce Robinson explaination about this circuit....
-
The following diagram is the schematic of simple easily tuned / adjustable sine and square wave oscillator. This circuit provides sine and square wave at frequency of below 20Hz up to above 20KHz. The benefit of this circuit diagram is that....
-
A multivibrator is an electronic circuit used to implement a variety of simple two-state systems such as light emitting diodes, timers and flip-flops. The monostable multivibrator will create a condition: in which one of the states is stabl....