Electronic Circuits Schematics Projects




Rolling-code generator uses flash microcontroller

Rating: 7.00/10 (26Votes cast)

Category: Computer Circuits / Memory Circuits
This circuit is also crossed to: PIC Microcontroller
Views: 2513
Rank: 0

This technology allows you to use a section of flash memory as if it were EEPROM. Because this µC is a true-flash device, the maximum number of erase/write cycles is typically 100,000 cycles. The flow chart in Figure 1 and the C code in Listing 1 show the adaptation of a textbook LFSR (linear-finite shift register) to the COP8 flash µC.An initial "seed" first drives the nput. The seed then traverses several exclusive-OR stages. The routine then saves the result to a virtual-EEPROMlocation. This approach allows an embedded-system designer to easily create a highly secure system visit page.

An initial `seed` first drives the nput. The seed then traverses several exclusive-OR stages. The routine then saves the result to a virtual-EEPROMlocation. This approach allows an embedded-system designer to easily create a highly secure system http://www.edn.com/article/CA82741.html

Related circuits

EPROM Programmer

The four 1K resistors on the output of U6 are too high in value for some parallel ports. Change these to 100ohm. Some LSI based parallel ports use active pull-up resistors and these are lower than the nominal 4K7 which causes a voltage divider effect. A bad design mistake. The eight LED dropper...



ATMEL 89C Series Flash Programmer

This programmer was designed in view of to be flexible, economical and easy to built, the programmer hardware utilizes the standard TTL series parts and no special components are used. The programmer is interfaced with the PC parallel port and there is no special requirement for the PC parallel...



FIFO makes cheap waveform generator

The circuit in Figure 1 shows the basic configuration of a simple and inexpensive arbitrary waveform generator. IC1s 82C54 produces the timebase for the wave table. This IC can generate a 152-Hz to 5-MHz clock under software control, which translates to a 1.52-Hz to 50-kHz, 100-point continuous...



FLASH ISP HANDBOOK

This application note describes the COP8 In System Programming (ISP) Software. ISP method of programming the flash memory are thoroughly discussed.



Buffered breakout box

The monitoring circuit consists of four tri-color LEDs driven by an equal number of op amps configured as gain-of-one inverting amplifiers. Each LED is wired in the circuit so that it glows red when the input to the op amp is high, and green when the input is low. The LED remains off when the...



Multiplexers convert FIFO buffer to bidirectional

The circuit converts a 32k½§16 SuperSync FIFO design to bidirectional (half-duplex) using QuickSwitch QS3390 16-to-8 multiplexer/demultiplexer ICs. This implementation has the following advantages over the traditional tristate-multiplex/demultiplex approach:



PAL powers universal ISA bus interface

A pc board bearing the 16-bit ISA data-bus interface in Fig 1 can adapt automatically to either 8- or 16-bit motherboard slots. The interface comprises three bidirectional octal buffers and glue logic. The glue logic controls transfer direction and output enables.



Flash Memory VPP Generator Reference Designs

The VPP generator circuits shown here cover a range of 30mA to 240mA with 3.3V or 5V inputs as noted. Table 1 summarizes these circuits for quick reference.



Articles & Projects
Several software / firmware upgrades have been successfully rolled out, which added new features and fixed bugs. Two different ... It has proven great when users with Java-only background could now easily be able to communicate with hardware, without needing to write any embedded code and without...

The top of the board is dominated by the microcontroller itself: a 60MHz NXP LPC1768 based on the eminently capable 32-bit ARM Cortex-M3 core, sporting 64K of RAM and 512K flash, and rounded out with an embarrassment of ... Also on top is the USB connector (mini-B), some power regulation circuitr...

In this post we will discuss the software or program or code written for moving message display project using microcontroller 8051. In this section, we will try to answer the issues related to the timings of the signals generated.

Schematic GSM modem interfacing with microcontroller 8051 for SMS control of industrial equipments circuit GSM modem interfacing with microcontroller 8051 for SMS control of industrial equipments microcontroller schematic. ... of SMS in text mode. code for the interfacing the GSM modem with micro...

(Note: Item Displayed is not the same as the circuit shown on this page) (CLICK ... It uses persistence of vision to let you drive the 64 led matrix with only 10 microcontroller outputs! ... Note: Check your email for the project code download link.

When you follow the schematics and burn the supplied hex file into the PIC, the circuit will work as it is supposed to (tested by many, many people who have already taken this course and by me as well). At this point ... Would you rather read this? Open assembler code [opens new window], Assemble...

PIC electronic dice - microcontroller.

How to make Scrolling LED display using 8051 microcontroller


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits