Display Circuits
- Page 5
-
This page features a replacement circuit for the LM3909 LED Flasher / Oscillator using discrete components. The circuit is functionally the same as the integrated LM3909 but has a minor variations in values of the components used. The LM3909 can still found....
-
-
The circuit is built using ICM7217 integrated circuit, manufactured by Intersil, which contains a CMOS counter up / down, with 4 digits and display properly. IC3 is the clock generator circuit which provides a square wave with period 1 s clock signal is....
-
-
You can make an LCD show a brief moving message by interfacing it to a microcontroller. Here`s an AVR-based moving-message display that uses a 16G—2 LCD display incorporating HD44780. The 16G—2 LCD can display 16 characters per line and there are two such....
-
-
The circuit shown here is of a simple 0 to 9 display that can be employed in a lot of applications. The circuit is based on asynchronous decade counter 7490(IC2), a 7 segment display (D1), and a seven segment decoder/driver IC 7446 (IC1). The seven segment....
-
-
The Mini 3 digit display aka "DVM-module" (digital voltmeter module) can easily be tuned and modified because you have control over the firmware. The key advantages of this module are: The internal reference voltage in the atmega8 microcontroller is 2. 56V.....
-
An LCD -liquid crystal display is an electronically-modulated optical device made up of any number of pixels filled with liquid crystals and arrayed in front of a light source (backlight) or reflector to produce images in color or monochrome. The block....
-
This Project is used to indicate the temperature and it is also used as controller. The system will get the temperature from the DS1820 and it will display the temperature over the LCD display. There are 2 preset levels, one is low preset and the other is....
-
-
I plugged the temperature onto 8 LEDs (I'm using a DeccanRobots package, and so this was supplied with the board). It worked, showing the temperature in binary form . Now when I tried using my microcontroller with this program I wrote to output the number....
-
-
A keyboard key figure who work with electrical contact between the surface of the keyboard and the underlying circuit when pressed keytop area, used by some home computers the early 1980s, and has been widely used in consumer electronic devices...
-
-
-
A universal digital gear display that can be installed on any motorbike. A low cost solution based on simple TTL digital technology without software programming....
-
This is a test project built hastily on a solder less breadboard. It uses a LM75 to read the current temperature via I2C and displays the result....
-
How to drive an dot matrix led display. This project shows you how to drive one with 64 LEDs (8 rows by 8 columns) or less e.g. 35 LEDs (7 rows by 5 columns)....
-
-
Liquid-crystal displays come in all sorts and sizes, and this applies also to their pinouts. In fact, many of these displays cannot be used properly without the manufacturers` documentation. But, of course, this can never be found when it is needed, and a....
-
A simple seven/7 segment counter circuit with an LED display. This counter circuit diagram is designed using IC CD 4033 as counter,555 Timer IC and seven segment LED Display LT 543....
-
This circuit suitable for a small office or home environment, it can also be adapted to use a combination lock or keypad to set and reset the ....
-
This is a circuit of 6 Zone Alarm with LED Display . This alarm system has 6 independent zones, a 7 segment LED display, 1 timed entry/exit zone ....
-
-
A segment may be tested by applying an alternating voltage of a few volts across it. Note that the application of a direct voltage will damage the display irreversibly: the resulting current will remove the tracks. The alternating voltage should contain not....
-
An automatic brightness adjustment is a closed loop system that has the capability to assess ambient light and adjust the brightness of the display accordingly. In ....
-
I`m doing this lab BCD COUNTER and 7 SEGMENT DISPLAY and im using CD4510BMS presettable BCD Up/Down Counter. I was able to do the counting from 00-99 but i can`t figure out the counting from 32-84. Do i need another gate for this operation Okay, sorry about....
-
I`m designing a circuit to drive a 4x7 segment display using a PIC. I`ve done this in the past without any drama. I would just use four pins to control each of the four digits (one each). I`d switch one digit on, wait a bit, turn it off, then switch the....
-
I have successfully used a 4511 IC to make numbers 1-9 appear on a 7 segment led display, cool. Now how can I use this to say have it display a number ....
-
An LCD basically consists of two glass plates with some liquid crystal material between them. The LCD has an electrically controlled light polarising liqui....
-
an easy to build, but nevertheless very accurate and useful digital voltmeter. It has been designed as a panel meter and can be used in DC power supplies or anywhere else it is necessary to have an accurate indication of the voltage present. The circuit....
-
The basic principle of the theremin is theheterodyne oscillator. When I started developing the Open. Theremin I knew that I needed a stable and reliable oscillator. So I searched the internet and found various schematics with different components. I built....
-