Electronic Circuits Schematics Projects




A/D Converter with LT1018

Rating: 4.00/10 (35Votes cast)

Category: Inside Circuits
Views: 1233
Rank: 3

The converter has a 60-ms conversion consumes 460 pA of 1's. 5 V power supply and maintains an accuracy of 10 bits on a 15 ° C in the temperature range of 35 ° C. A pulse applied to convert the command line causes Q3, operating in reverse mode, the discharge path through the diode 10 kO, forcing its collector low. Q3 results of reverse mode switching in a capacitor discharge to 1 mV of ground. During the time of the ramp value is less than the input voltage, output of the CIA is low.
A/D Converter with LT1018



This allows pulses ClB stabilized quartz oscillator, modulating Q4. The output data appears at the collector of Q4. When the ramp crosses the starting value of the output voltages of the CIA is going up, Q4 polarization and output data continuously. The number of pulses at the output is directly proportional to the input voltage. To celebrate cali apply 0.5V to the input and the TRIM-10 kO exactly 1000 pulses each time the conversion from the command line is pulsed.


Datasheet file1: Click here to download 2N5089.pdf datasheet.

Datasheet file2: Click here to download LT1034.pdf datasheet.

Datasheet file3: Click here to download HP5082.pdf datasheet.

Datasheet file4: Click here to download 2N5087.pdf datasheet.

Datasheet file5: Click here to download 2N3904.pdf datasheet.

Datasheet file6: Click here to download LT1018.pdf datasheet.


Related circuits

Astable

This astable will trigger itself and run free as a multivibrator. The external capacitor charges through RA and RB and discharges through R8 only. Thus, the duty cycle is set by the ratio of these two resistors, and the capacitor charges and discharges between 1/3 Vs and 2/3 Vs.



Solid-state-relay

A higher Iiue voltage can be used if the diode, varistor, ZVS, and power thyristor settings are at compatible levels.



LED tilt level

This electronic level uses two LED indicators instead of an air bubble. If the surface is tilted to the right, one LED lights; if it's tilted to the left, the other LED lights. When the surface is level, both LEDs light. It uses two unidirectional mercury switches, SI and S2. The unidirectional...



Fiber-optic link

Fiber Optic applications require analog drivers and receivers operating in the megahertz region. This complete analog transmission system is suitable for optical communication applications up to 3 MHz. The transmitter LED is normally biased at 50 mA operating current. The input is capacitively...



Automotive Audible-Turn Indicator Circuit

This little circuit should be useful to the hearing impaired. It produces a tone each time a dashboard turn indicator lights.



Saw-oscillator-modulator

Adding a diode, a resistor, and a capacitor to the SAW (surface-acoustic-wave) oscillator allows you to use the oscillator in FSK (frequency-shift-keying) applications. Dl, Rl, and Cl form a simple diode switch in which Dl shunts Cl to ground. When the digital FSK input to Rl is low, Dl is off,...



Inexpensive Pulse Generator For Logic Troubleshooting

Built around a 555 timer IC, this pulse generator can be built into a probe for logic



Crystal Controlled Frequency Converter Circuit

The second gate (G2) of a MOSFET can be used to incorporate a crystal oscillator into the same stage as a frequency mixer. Although old hat with tubes, this scheme is seldom seen in dual-gate MOSFET circuitry. L3, 03, and XI form the crystal oscillator, and T2 is an IF output transformer. T1 and...



Articles & Projects
02 TJ 145k Miles 32 RH 3 Speed Check Engine light turned on today, pulled up the code and it read P0740 for the TC. Its strange because I had the same.

Here is the circuit diagram of a effective light to frequency converter circuit that can be used for variety of applications such as light intensity measurement,fun etc.The circuit is based on TLC555, the CMOS version of famous ...

Speaker to microphone converter circuit. This circuit is a simple approach for converting a loud speaker into a microphone. When the sound waves fall on the diaphragm of a speaker, there will be fluctuations in the coil and ...

Mosfet Snubber Circuit in Flyback Converter , Typical flyback convertor with drain clamping circuits ZenBlock Zener with integrated blocking diode Philips Semiconductors new ZenBlockTM replaces double-diode-, RCD- or RC-snubbers in ...

This is a design for DC to DC converter module. The module is a device that accepts a DC input voltage and produces a DC output voltage. Normally the output voltage produced is at a different voltage level than the input.

Hi there, Quick question, In a theoretical project, what would be the max voltage a Bridge rectifier circuit with a capacitive filter could take ? Does anyone know a more efficient to transform AC - DC at higher voltages ?

data converter fundamentals - 1 (Mixed Signal Electronics & Circuit Design)

Data Converter Fundamentals II (Mixed Signal Electronics & Circuit Design)


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits