Electronic Circuits Schematics Projects




Car Voltmeter Circuit

Rating: 2.00/10 (23Votes cast)

Category: Inside Circuits
Views: 528
Rank: 2

This screen uses ten LEDs to display a voltage range of 10.5 to 15 volts. Each LED represents a step 0.5wvolt tension. The heart of the circuit is the 3914 points LM / bar display driver. Trimming potentiometer R5 is adjusted so that 7.5 volts is applied to the upper side of the bulkhead. D2 resistor R7 and diode D5 to tighten the voltage applied to the LED 3 volts. A lowpass filter consisting of L1 and C2 guards against voltage spikes.
Car Voltmeter Circuit



The diode D1 is used to protect against reverse voltage where the voltmeter is connected backwards.

Related circuits

Crystal controlled butler oscillator

A typical Butler oscillator (20-100 MHz) uses an FET in the second stage; the circuit is not reliable with two bipolars. Sometimes two FETs are used



Video amplifier and video detector

The circuit has a typical voltage gain of 84 dB and a typical AGC range of 80 dB. It gives very small changes in bandpass shape, usually less than 1 dB tilt for 60 dB compression. There are no shielded sections. The detector uses a single tuned circuit (L3 and CIO)



Low-Consumption Monostable Relay

A monostable relay has two states: operative when a large enough current flows through its coil and quiesc



Pulse Train

This circuit has a rate multiplier using a 4093 Schmitt trigger as an oscillator, driving a 4017 decade counter. When a pulse p



Tilt-meter

Electrodes are immersed in an electrolyte that remains level while the sensor follows the tilt of the body on which it is placed, more of one outer electrode and less of the other are immersed and their resistances fall or rise, respectively. The resistance change causes a change in the output...



Pierce oscillator

The oscillator transistor is Ql, and the crystal is placed between the collector and base. Feedback is improved by the use of the collector-emitter capacitor C2



Manual Headlight/Spotlight Control For Autos Circuit

Pressing the START pushbutton turns on either the headlights or spotlights for a predetermined time. After 1 minute (Rl and CI determine this),



Transmitter Negative Key Line Keyer

Using an NTE288 (or ECG288, GE223, or SK3434), this circuit can key a negative line up to - 300 V maxim



Articles & Projects
This is a very useful circuit which when installed on your car gives the voltage of you car battery in a LED dot display form.The circuit is based on four comparators made of quad op amp LM324.The inverting inputs of IC are ...

Easy Provider LED Car Auto Battery Electric Cigarette Lighter Voltmeter Voltage Meter Tester | digitalmultimeter.biz.

Circuit diagram: LED-Volt-Meter-circuit-diagram12 LED Volt Meter Circuit Diagram. http://streampowers.blogspot.com/2012/06/led-volt-meter-circuit.html. Related Posts : circuit, led, meter, volt. TA8210AH car audio amplifier ...

Buy Now! Today Lowest Price: Find & Check latest Low Price Order Now! Mini LED Display Digital Car Voltmeter 12V/24V Vehicle Voltage Gauge Product By ePathDirect No customer reviews yet. ( customers reviews) List.

In the figure is a design circuit that was developed to create a voltmeter that will be used to test car batteries while showing an indication using LEDs. This is the figure of the circuit;..The voltage of a car battery can be ...

The post discusses a simple digital voltmeter circuit using the IC L7107 which can be used as a digital panel voltmeter for workbench requirements. ... It ensures auto zero correction for inputs less than 10uV, a zero drift for inputs below 1uV/oC, bias current for inputs of maximum 10pA and cros...

Electric troubleshoot with a voltmeter. Circuit with 2 switches Part 3

How to use a Multimeter for beginners: Part 1 - Voltage measurement


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits