Electronic Circuits Schematics Projects




Touch Switch with MPF102 JFET

Rating: 2.00/10 (8Votes cast)

Category: Inside Circuits
Views: 1022
Rank: 0

When the touch plate is contacted by a large object (human body, etc.), stray 60-?? pickup is rectified by D1 and D2, and produces a negative voltage across R2-C2 and the gate of Q 1. Q1 cuts off, causes Q2 to conduct, and the output goes low.
Touch Switch with MPF102 JFET



Q2 is held cut off since Q1 normally is conducting.

Related circuits

50Mhz-trigger

This has a stable trigger 100 m V sensitivity at 50 MHz. The FETs comprise a simple high-speed buffer and the LT1016 compares the buffer"s output to the potential at tbe trigger level potentiometer, which can be of either polarity. The 10-KO resistor provides hysteresis, eliminating...



Four-Trace Oscilloscope Adapter

This simple adapter uses an oscillator (567) to drive a counter (U2) and switch (U3) that selects the outpu



Phase reversal detector

Assume the correct phase sequence to be VA-VB-VC. The circuit terminals are connected such that Tl gets connected to phase A and T2 to phase B. The capacitor advances the voltage developed across R2 due to phase "B" by — 60°, while the voltages developed across it by phase "A" is in phase with...



80M And 40M Cw-Ssb Receiver Circuit

This direct-conversion receiver uses a TDA7000 IC and it drives an LM386 audio amplifier. The TDA7000 is used for its mixer and L.O. section.



10000Vdc Supply

A CMOS oscillator (U1A) drives. U1B through U1F, which drives Ql, which generates a 12-Vpp square wave across the primary



Temperature-to-frequency converter

Al's positive input is biased by the thermocouple. Al's output drives a crude V — F converter, comprised of the 74C04 inverters and associated components. Each V — F output pulse causes a fixed quantity of charge to be dispensed into the 1 µ¥ capacitor from the 100 pF capacitor via the...



Boat alarm

Removing R1 or R2 from the circuit the potential thief breaks a hidden wire that connects R1 to +12 V and R2 to ground)



Wide-range-voltage-to-frequency-converter

This circuit is based upon the change of frequency of the function generator with the input voltage ViN· Generally, the frequency depends upon the capacitance and resistor connected to pin 6. This resistor is replaced by the FET.



Articles & Projects
Electronics Project for Students and Hobbyist. Learn by Circuit Diagram.

The modern mechanic switches are improved concerning of old technology. We need however many times to replacement some old switch or to check currents bigger than the durability of certain switches or simple we need ...

This is a circuit for touch switch circuit. This circuit is almost same with touch door alarm. This circuit uses a 555 timer as the bases of the touch switch circuit. This is the figure of the circuit. The operation of this circuit is begin, ...

This is a touch circuit that is used as a latching circuit to switch a LED ON and OFF by physically touching the ON metal plate or OFF metal plate. This circuit is based on logic gate for control the operation. This is the figure of ...

This is touch switch circuit diagram.Here I have used ... This circuit operates with 5V to 12V. ... Labels: circuit, diagram, switch, touch ... The following schematic shows a Ding Dong Door Bell Circuit Design using 8021-2 IC .

This circuit is designed to generate a 20KHz pseudo sine wave signal that can power about 50 remote touch activated switch circuits. It can support a cable length of about 2500 feet. A typical remote switch circuit is also ...

How to make Touch switch using NE555- www.buildcircuit.com

How the Capacitance touch sensor (button-switch) works


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits