Electronic Circuits Schematics Projects




White-LED driver backlights LCD and keypad

Rating: 4.00/10 (100Votes cast)

Category: Light Laser LED Circuits / Led circuits
This circuit is also crossed to: LCD circuits
Views: 3660
Rank: 0

Figure 1 shows a method for driving all the LEDs with a single driver IC from Catalyst Semiconductor (www.catsemi.com), the CAT32. Power comes from a single lithium-ion battery cell. A FET switch can independently turn off the group of six LEDs. The shutdown input, , on the CAT32 turns off all the LEDs. LED brightness is a direct function of the current running through the LED, and typical values are 10 to 20 mA for white LEDs. The CAT32 regulates a constant current through the LED pin. Resistor R1 connected to the RSET pin adjusts the LED current. visit page.

Related circuits

LED tilt level

This electronic level uses two LED indicators instead of an air bubble. If the surface is tilted to the right, one LED lights; if it's tilted to the left, the other LED lights. When the surface is level, both LEDs light. It uses two unidirectional mercury switches, SI and S2. The unidirectional...



ALPHANUMERIC LED DISPLAY PROJECT

A tiny sandwich flag connected perpendicular to the motor spindle aids observation of how long it takes to complete one full rotation. This worked initially, as each burst from the capacitor barely moved the flag 1/4 of a rotation. As the circuit variations became more efficient and powerful (the...



LED Flash Driver with HT2050

This circuit is based around HT?2050 manufactured by HOLTEK semiconductors. It is a low cost, low-power C-MOS LSI designed for lamp andLED flash driver. It requires minimum external components.You can operate it with just two AAA cell or 3v Battery.Circuit has five flash outputs with 10mA drive...



LED Torch

The LED Torch is based on a 7555 timer running in astable mode (do not use an ordinary 555). A white LED (Maplin order code NR73) produces 400 mcd light output, which, when focussed, can illuminate objects at 30 metres. Try Conrad Electronic for what appears to be a stronger white LED (order code...



Solar Charged LED Utility Light

There are 3 series strings of LEDs in this circuit, the resistors limit the current through the LEDs and prevent them from burning up. The white LEDs have a higher voltage drop and only 3 can be used in series with a 12V (11-13V) source. The red/orange/yellow LEDs have a lower voltage drop per...



25 white LED Driver

The LED circuit below is an example of using 25 white LEDs in series connected to the 120VAC line. It can be modified for more or less LEDs by adjusting the resistor value. The exact resistance will depend on the particular LEDs used. But working out the resistor value is a bit complicated since...



DC/DC LED Driver in ThinSOT

The LT®1932 is a fixed frequency step-up DC/DC converter designed to operate as a constant-current source. Because it directly regulates output current, the LT1932 is ideal for driving light emitting diodes (LEDs) whose light intensity is proportional to the current passing through them, not the...



1.5V LED FLASHER VERSION A

Many published circuits that flash LEDs need 3 volts or more. This circuit uses only a single inexpensive C-MOS IC and flashes the LED for a full year on a single 1.5 volt AA alkaline battery cell. The circuit uses a charge pump technique to provide the LED the needed voltage.



Articles & Projects
The LED driver circuit will be the next spot, then check all the corresponding LED+ and LED- connections down to each of the keypad and LCD white LED. Nokia C2-00 Keypad and LCD Display Backlight Connection Tracks ...

Solution for Nokia 2710 LCD screen display backlight LED not working. Nokia 2710 Display Lcd Light Probelm Solution Jumper. The solution above showed the LCD and keypad backlight LED driver circuit. this circuit holds ...

We already have the keypad light solution postedhere, so this gonna be a continuation of the white backlight LED troubleshooting for Nokia C2-03. This will also work ... Take note: the LCD's backlight is also connected in parallel circuit like the two LED's on the flex - meaning if that two LED's...

Space-constrained applications, such as handsets, glucometers and other portable devices that require illumination of LCD displays and keypads, now have a linear LED driver option that can save up to 60 percent board ...

There are two white LED light used in in illuminating the keypads, it may also get damaged due by water, wet or cause by oxidation build ups. The solution below shows the ... It also shows which nearby particular components it is being connected or part of the keypad back lighting circuit. Here's...

Diodes Incorporated 9-channel LED drivers improve LCD backlighting performance with 93% efficiency and 1% channel matching. Date Announced: 04 Oct 2010. Dallas - Diodes Incorporated, a leading global manufacturer and supplier of ...

17" TFT LCD BRIGHTVIEW WIDESCREEN DISPLAY PANEL DV9700 (SALE) 507418-001

Nokia 1600 key pad IC changing.


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits