Electronic Circuits Schematics Projects




Delay switching for power amplifiers

Rating: 3.00/10 (89Votes cast)

Category: Power Supply Circuits / AC to DC & DC to DC
This circuit is also crossed to: Amplifiers , Relay Circuits , Switching Circuits , Delay Circuits
Views: 1582
Rank: 0

This delay can be used in power amplifiers, to prevent the fuses fail when the amplifier is turned on. The circuit is very simple with a relay which turned on when C2 and C3 are charged. If the relay has not been applied, the resistors used to control connected to feed. If after some time the relay attracts the bridge resistors. Watch out for your own safety when building this circuit. On the whole circuit is power. F1 should be the value of having the fuse that normally would be used.R1, R2 = 470 kOhm R3 = 220 ? R4-R7 = 10 ? / 5 W wirewound C1 = 330 nF 400 V ~ X2-type C2-C3 = 470 uF 40 - 63V B1 = B250C1500 RE1 = 250 ? 24 V 1200 V / 8 A Contacts F1 = see text visit page.
Delay switching for power amplifiers



R1, R2 = 470 kOhm R3 = 220 ? R4-R7 = 10 ? / 5 W wirewound C1 = 330 nF 400 V ~ X2-type C2-C3 = 470 uF 40 - 63V B1 = B250C1500 RE1 = 250 ? 24 V 1200 V / 8 A Contacts F1 = see text http://www.circuitsonline.net/schakelingen/93/voedingen/inschakelvertraging.html

Related circuits

Electronic crowbar for AC or DC lines

For positive protection of electrical or electronic equipment, use this against excessive supply voltage. Due to improper switching, wiring, short circuits, or failure of regulators, an electronic crowbar circuit can quickly place a short circuit across the power lines, thereby dropping the...



12 Volt DC to 120 Volt AC Inverter

Ever needed a low power 120volt AC power source for your car, van or truck? Well this circuit should do the trick for you. It will supply 15 watts of AC power to a device. It should power lamps, shavers, small stereos and small appliances. If you draw to much power the circuit will shut down all...



Efficient-supply-splitter

In this application, the Vl-7660 is connected as a voltage splitter. Note that the normal output pin is connected to ground and the normal ground pin is used as the output. The switches that allow the charge pumping are bidirectional; therefore, charge transfer can be performed in reverse.



12V to 6V Converter

This small but useful circuit is a DC voltage convertor for using 6V devices with car battery voltage. The maximum output current is dependent if the T1 is covered with a proper heat sink or not. You can use the circuit to drive devices that they sink maximum 0.5A current without any heat-sink...



Power pack for battery-powered devices

This circuit gives a regulated output of between 5 V and 15 Vdc, adjusted and set by a preset resistor. Current output up to about 350 mA



Power Supply

When working with electronics, you always need one basic thing; power. This power supply is great for powering all kinds of electronic projects. It produces a well filtered, variable 1.2-30 volts at 5 amps. It is easy to build and the parts are easy to find.



Combination Voltage And Current Regulator Circuit

This voltage-regulator/cuiTent-liimter combination can be made from two 7805 regulators as shown. Rl, R2, and R3 shouldbe selected for a 5-V drop at the maximum allowable currant limit. SI selects one of the three current values. Do not forget that Ul requires 5 mA to operate and this means that...



POWER SUPPLY 15V 4A

This is an image Schematic. No Description available.



Power Off Time Delay Relay Circuit

Light ON/OFF Delay Relay in Car Electronics


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits