Electronic Circuits Schematics Projects




STK200/STK300 ISP Header

Rating: 7.00/10 (44Votes cast)

Category: Microcontroller Circuits / AVR Microcontroller
This circuit is also crossed to: , Buffer Circuits
Views: 2613
Rank: 0

If you`ve got a friend`s STK200/STK300 ISP cable, here is the signal designation needed to be tied to AVR chips. If you don`t have it, let build the buffer cable that compatible with STK200/STK300 and try also a free download `ATMEL AVR ISP` from ATMEL website.The necessary signal needed for AVR ISP are MOSI, RESET, SCK, and MISO. In addition, the DC supply +5V and GND are provided by the application board for the ISP buffer chip. See the circuit diagram of the ISP buffer chip here "Experimenting the AVR m visit page.

The necessary signal needed for AVR ISP are MOSI, RESET, SCK, and MISO. In addition, the DC supply +5V and GND are provided by the application board for the ISP buffer chip. See the circuit diagram of the ISP buffer chip here `Experimenting the AVR m http://www.kmitl.ac.th/~kswichit%20/STK300/Stk300.html

Related circuits

Solar tracking System with AT89C2051

This is a power generating method from sunlight.This method of power generation is simple and is taken from natural resource. This need only maximum sunlight to generate power. This project helps for power generation by setting the equipment to get maximum sunlight automatically. This system is...



Digital Telemetry with ATMega8

The ATmega8 microcontroller-based Low-Cost Telemetry Device (LTD) is an efficient telemetry keyer. The LTD measures the voltage levels of up to four analog channels via its on-chip 10-bit ADC, converts the measurements to numbers, and then sends the data in Morse code to an external transmitter...



Very Low Noise Pick-up Preamplifier

The preamplifier was designed to signal sources such as low-impedance moving coil cartridges (MC) on turntables high fidelity (and yet still there). The impedance of the amplifier is 100 W. To keep the noise levels low, three double-type transistors MAT03 SSM2220 or linked together to form a...



Digital event Counter AT89C2051

Digital visitor counter is a reliable circuit that takes over the task of counting Number of Persons/ Visitors in the Room very Accurately. When somebody enters into the Room then the Counter is Incremented by one and when any one leaves the room then the Counter is Decremented by One. The total...



Wireless Coupled Scanning Voltmeter (ATMega8)

A 10 bit scanning voltmeter with a Minimum Mass Wireless Coupler, based on the ATMega8.Range to the Minimum Mass Base Unit is 10 to 15 cm. If the voltmeter is battery operated, it can be floated from ground. This project is very simple physically, intended to demonstrate how easily the Minimum...



LCD Oscilloscope using AVR MC

This is one of great project based on AVR microcontroller. It use ATmega 32 as processor and LCD 128x64 pixels for display. If you need to measure low frequency i thought this project, AVR oscilloscope, will be usefull. Maksimum frequency for AVR oscilloscope is 5 kHz (square signal), other...



Circuit programs Atmel AVR microcontrollers

Atmel AVR µCs feature an enhanced RISC architecture that purportedly offer the highest MIPS-per-milliwatt capability in the 8-bit µC market. Figure 1 shows an easy-to-build AVR µC-programming circuit that can program the 40-pin AT90S4414/8515, the 20-pin AT90S1200/2313, and the eight-pin...



Night Light Saver II

The design features low cost, easy installation, no battery backup and no EMI. The AT89C2051 uses external oscillator generated by schmitt trigger gate CD4093, ~680kHz. Reference frequency was derived from 50Hz main line. Time setting only allows at 18:00 by pressing time set button once. If main...



Features of In-Circuit Programming

How to program the AVR microcontroller Pt 1


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits