Electronic Circuits Schematics Projects




Voltage Inverter

Rating: 3.00/10 (44Votes cast)

Category: Power Supply Circuits / AC to DC & DC to DC
This circuit is also crossed to: Timer Circuits
Views: 1529
Rank: 4

This simple circuit is a good solution to the powering a dual supply op amp from a single battery problem. The circuit simply takes a positive voltage and inverts it. It uses only one 555 timer and a few other passive components, so it doesn`t add much in the way of size and cost to a project. visit page.

Related circuits

Variable DC Power Supply

A Variable DC Power Supply is one of the most useful tools on the electronics hobbyist`s workbench. This circuit is not an absolute novelty, but it is simple, reliable, "rugged" and short-proof, featuring variable voltage up to 24V and variable current limiting up to 2A. Well suited to supply the...



Basic UPS Power Supply

This circuit can be adapted for other regulated and unregulated voltages by using different regulators and batteries. For a 15 Volt regulated supply use two 12 Volt batteries in series and a 7815 regulator. There is a lot of flexibility in this circuit.



Variable power supply

T1 steps down AC voltage from 115VAC (or 220VAC) to about 8VAC and is then rectified via bridge rectifier BR1 to about 11.52Vdc. C1 filters off the AC ripple. If you find the circuit output too noisy add another electrolytic capacitor over the output terminals. Value can be between 10 and...



Regulator Loss Cutter Circuit

Large input-to-output voltage differentials, caused by wide input voltage variations, reduce a linear regulator`s efficiency and increase its power dissipation. A switching preregulator can reduce this power dissipation by minimizing the voltage drop across an adjustable linear regulator to a...



General-purpose-power-supply

The supply 6-66 can be used for supply output voltages from 1 to 35 V. The line transformer should be selected to give about1.4 times the desired output voltage from the positive side of filter capacitor C1 to ground. Potentiometer R2 sets the output voltage to the desired value by adjusting...



Dual Polarity Power Supply

This dual polarity power supply is easy to build, requires few parts, and is adjustable from 0-15 volts. It is great for powering op amp circuits, as well as other circuits that require a dual supply voltage.



Precision AC/DC Converters

Although semiconductor diodes available today are close to ideal`` devices, they have severe limitations in low level applications. Silicon diodes have a 0.6V threshold which must be overcome before appreciable conduction occurs. By placing the diode in the feedback loop of an operational...



Variable Voltage Regulation

As Ron suggests, controlling the output voltage from a regulator can be made variable in three ways. Using a fixed reference zener diode to increase the output by the value of the zener. A variable resistor for variable output, note that a voltage less than the nominal regulator is not possible....



Articles & Projects
This inverter circuit works with a transistor and transformer and other components to increase the voltage becomes high. Input supply voltage ranging from 3V to 6V DC, later it was raised to high voltage AC. However, in this ...

This circuit uses a step-up switch-mode regulator, which is usually used to produce a positive supply, to generate a regulated negative output voltage. The device used here is the MIC4680 from Micrel (www.micrel.com), but ...

In many circuits we need to generate an internal adjustable voltage. This circuit shows how it is possible to use a trusty old NE555 timer IC and a bit of external circuitry to create a voltage inverter and doubler. The input voltage to be doubled is ...

In the model, an ideal DC voltage source is used, and the DC power drawn by the circuit is measured. The three-phase inverter uses six IGBT blocks in parallel with six free-wheeling diodes. Device parameters come from the ...

Inverter circuit on basic of really taking a series of mosquito racket, a racket in which these mosquitoes require only a low voltage. With only 3 Volts course of this series has been able to work. Circuit is raising the voltage by a ...

The following post shows how a full bridge 1 KVA inverter circuit can be built using 4 N-channel mosfets, without incorporating complicated high side driver networks or chips. Driving a full bridge mosfet network having 4 N-channel ... The output of the NOT gates which are configured as buffers g...

Transistor DC to AC power inverter

DC - DC Boost Converter (DANGER HIGH VOLTAGE!) (HD 720p)


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits