5V / 2A isolated switching power supply circuit diagram

  
Circuit is shown. C1 is the input filter capacitor. VDz VD1 composition and primary clamp .png">protection circuit . The control
5V / 2A isolated switching power supply circuit diagram - schematic

terminal of the resistor R1, C2 is a bypass capacitor. TOP414GC-S parallel between the end of the C10 is to prevent high-frequency interference appears on the control side sometimes cause power outages trigger circuit malfunction. VD2 output rectifier diode, output filter C3, C4, L, C5 and C6 constituted, C9 as an output capacitor noise cancellation. External error amplifier by a TL431 shunt regulator composition. When the output voltage fluctuates, by R3, R4 after the voltage obtained by dividing the sample voltage, the TL431 with a reference voltage, and generates an external control signal, and then to change TOP414G control terminal current through optocoupler PC817A, thereby regulating the duty than make Uo stabilize. Control loop gain is set by R2. After the feedback winding voltage VD3, after C7 rectifier to PC817A the infrared receiver power supply.



Recommended videos


  • Switch mode power supply tutorial: DC-DC buck converters
    Duration: 10:05.
  • Free Circuit Diagrams - Self Switching Power Supply
    Duration: 1:31.
  • SMPS Tutorial (5): Inductor Basics, Magnetic Circuits, Switched Mode Power Supplies
    Duration: 26:44.

News


  • Is stories
    IXYS Corporation, designs, develops and markets power semiconductors used primarily in controlling energy in motor drives, power conversion (including uninterruptible and ) and medical electronics. IXYS' power ...
     24 February 2017
  • Electronics EETimes (registration)
    Electronics EETimes (registration) industryThe overall market for AC/DC and DC/DC commercial (C-), which excludes consumers and uninterruptible (UPS), is estimated to be worth between 22 and 25 billion US Dollars. The market has been s
     23 February 2017
  • Highland Mirror
    ... into multiple applications, including exciting alternatives in ighter and more-tunable light for general illumination, backlighting for more-vivid displays, optimized power management for high-current and variable-speed
     23 February 2017
  • Engineer Live
    The device is employed in an array of electronic devices and equipment, including high voltage regulated , power supplies, UPSs, AC-DC adapters/chargers, DC-DC converters, lighting circuits, industrial ballasts, temperature and ...<
     21 February 2017
  • Hackaday
    They are AM receivers from an era with a low electrical noise floor, so they don't react well to high-frequency . Thus, the inverters usually tasked for projects like this are low-frequency, at 50Hz as this is a European
     20 February 2017
  • ThomasNet News (press release) (blog)
    ThomasNet News (press release) (blog) Used in , UPSs, DC-DC converters, lighting circuits, industrial ballasts and motor speed control circuits, SD560B Rectifier is designed with 5 A IO rating, 600 V VRRM and 200 A IFSM rating. Minimizing rev
     13 February 2017
  • ThomasNet News (press release) (blog)
    ThomasNet News (press release) (blog) Reducing start-up loss, CRD-060DD17P-2 Demonstration Board is operated in 300 V to 1000 V input voltage range. Delivering 48W of power, unit is designed with 1700 V SiC MOSFET. Suitable in auxiliary and
     13 February 2017
  • Hackaday
    Hackaday That's a total current requirement of almost 125 amps at 5 V. Add in all the Arduino's, and [Robert] needed a beefy 750 W of power, supplied via four . Each Arduino Nano is a slave on the I²C bus. The I²C master is an Ardui
     11 February 2017
  • Electropages (blog)
    Electropages (blog) designed for harsh environmentsPowersolve has a new family of encapsulated AC/DC designed specifically for harsh environments. Typically these will include security, CCTV and LED installations. For maximum applicatio
     8 February 2017

.