Transceiver Circuits
- Page 2-
One day on the 50MHz SSB-QSO, my friends JE3TXU/1 (Mr. Haraguchi) sad to me that he made 50MHz very small transceiver. I said to him that he shall inform about it on the Japanease CQ magazine. You can see about it on the book. See the photo! This rig is made.... -
The 7MHz CW transceiver made with MC3362P. I made a 7MHz CW transceiver by using the IC for the narrow band FM double super receiving circuit, MC3362P. I intended to make a transceiver for 10MHz band in the beginning. But, I was worried by the neighboring.... -
The choice of IF is usually determined from availability of filters with desired characteristics. For communication receiver or transceiver the requirements for main selective element are very high, and usually two types of filters are used:.... -
The ATA5743 is a multi-chip PLL receiver device supplied in an SSO20 package. It has been especially developed for the demands of RF low-cost data transmission sys- tems with data rates from 1 kBaud to 10 kBaud in Manchester or Bi-phase code. The receiver is.... -
The ATR0981 is a monolithic IC manufactured using Atmels advanced SiGe technol ogy. The IC performs a transmit and receive front-end function, dedicated for a frequency range of 300 MHz to 500 MHz. It consists of a Low-Noise Amplifier (LNA) and a Power.... -
The MLX90224 series are dual Hall effect Latches It includes two Hall effect latch functions of which typical thresholds are +/- 2. 0 mT. In each latch, the magnetic flux detection is performed by a switched silicon Hall plate. The BOP and BRP are.... -
This design note presents a simple yet feature loaded 16 watt output, universal AC input adapter power supply for modems, hubs or similar applications. The circuit is a discontinuous mode (DCM) flyback converter topology designed around ON Semiconductor`s.... -
In this circuit SP6126 is configured as a Zeta converter to provide 0. 3A for driving four series-connected LEDs The SP6126 is a flexible and economical controller that provides the necessary functions required by a Zeta Regulator This report includes the.... -
The receiver is a tripple superheterodyne receiver with two PLL-guided local oscillators. The first LO (2. 1 GHz) can be set in steps of 500kHz and sets the RX signal down to 188 - 188. 5 MHz. It has a high PLL loop bandwidth of around 20kHz, therefore gives.... -
The microphone amplifier / modulator is build around LM324 which is a quad op amplifier provides enough quality amplification to voice picked up by the condenser microphone... -
Microphone amplifier consists of LM324 and two transistors. LM324 is available in 14 pin DIP. I brought it for Rs: 6/-. It contains four identical operational amplifiers. Transistors BC548 and BC558 are used as compressor. I used 2-wire shield wire for.... -
The 751 required turning the volume control almost to 12 o`clock before getting any hearable volume so I thought maybe something was wrong here. I replaced all the electrolytics associated with the audio path, i. e. after the detector stage and the audo amp..... -
The Intersil ISL43485 is a high speed BiCMOS 3. 3V powered, single transceiver that meets both the RS-485 and RS-422 standards for balanced communication. Unlike some competitive devices, this Intersil transceiver is specified for 10% tolerance supplies (3V.... -
These Intersil RS-485/RS-422 devices are "fractional" unit load (UL), BiCMOS, 5V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication. Unlike competitive devices, this Intersil family is specified for 10%.... -
These Intersil RS-485/RS-422 devices are BiCMOS 3. 3V powered, single transceivers that meet both the RS-485 and RS-422 standards for balanced communication. Unlike competitive devices, this Intersil family is specified for 10% tolerance supplies (3V to 3..... -
This article presents a description of a 70cm wideband transceiver for duplex operation. The modules are designed for operation in a 200 kHz wide duplex channel, freely selectable from 430-440 MHz with a 100 kHz channel spacing. First prototypes were.... -
This project is designed for the entry level laser experimenter. The circuit allows any two computers with serial (RS-232) communication capability to communicate over 200 meters using a laser beam. A low cost transmitter only circuit is also presented here.... -
The 6JS6C tube is a TV Deflection Tube, or "Sweep Tube". Although not meant for transmitting, it exhibits sufficient performance for RF operation through 30 MHz. Each tube can dissipate 30 watts of plate power. The base is a 12-pin socket. There will come a.... -
The RF signal is split into two signals that are shifted 90 degrees out of phase (one plus 45 and one minus 45 degrees). Both are mixed to audio frequencies. The two audio signals are again shifted 90 degrees out of phase (again one plus 45 and one minus 45.... -
The performance of the 80 meter CW transceiver using the phase method for side band suppression is very good. Construction was easy with all good obtainable standard electronic components and without the expensive or complex crystal filter. Almost nothing is.... -
The main characteristic of the transceiver presented below is the simplicity, but in the same time giving good performance, with a minimum investment. The radio is based on MC3362 ( buy ). This integrated circuit its an FM receiver, double conversion, which.... -
DDS VFOs work very well with single conversion SSB radios such as the Codan 6801, 6924, 7727 and 8121, and the AWA Teleradio 110H. See the Recycled Radios page for more information about suitable Codan radios. Other commercial and marine transceivers with....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
The sunset lamp comes on at full brightness and then slowly fades out over 1.5 hours time and...
The circuit monitors the input to the microprocessor 5 V regulated supply for voltage drops and...
The Accu charger circuit is very simple and easy to make, because it only requires a few...
Although not a new device, the LM317 is still a high-performance regulator. Its output voltage is...
This simple adapter circuit is specially intended for use with the USB Audio DAC published in...
A very simple 5 volt constant voltage, constant current (CV/CC) universal-input power supply for...
Detecting electrical equipment, sometimes in order to more accurately measure the electrical...