A very small but good quality amplifier circuit that is also fairly cheap. It is based on TDA2002 which offers very low distrortion. Power should be 12-15 volt 1,2A. The amplifier frequency responce ranges from 40Hz to 15Khz. A good heatsink is required. At the input you can connect your mp3 player or your pc audio out etc...
This linear amplifier delivers 10-W PEP output; with 1.25-W drive on 10 m. Tl, T2, and T3 are 10 turns of bifilar windings on an FT-50-43 toroidal core. The transformers are broadband. Filters for other bands, if desired, are shown. Note: use #26 wire for C1 and C2. Use capacitors that are closest to these suggested values. As the operating frequency decreases, the gain will Increase as well as the possibility for instability. You may have to use RC feedback to negate.....
This broadband amplifier covers the 225-400 MHz military communications band producing 10 watt RF output power and operating from a 28 volt supply. The amplifier can be used as a driver for higher power devices such as 2N6439 and MRF327. The circuit is designed to be driven by a 50 ohm source and operate into a nominal 50 ohm load. The input matching network consists of a section composed of C3, C4, Z2, C5 and C6. C2 is a dc blocking capacitor, and Tl is a 4:1 impedance.....
The aim of this design is to reproduce a Combo amplifier of the type very common in the `sixties and the `seventies of the past century. It is well suited as a guitar amplifier but it will do a good job with any kind of electronic musical instrument or microphone. 5W power output was a common feature of these widespread devices due to the general adoption of a class A single-tube output stage (see the Vox AC-4 model). Furthermore, nowadays we can do without the.....
Ideal to operate 3 to 24V DC existing on-circuit lamps LED operation is also possible. This circuit was designed to provide that continuous light lamps already wired into a circuit, become flashing. Simply insert the circuit between existing lamp and negative supply. Especially suited for car or panel pilot lights, this device can drive lamps up to 10W...
The LCDs reduced size and power requirements allow much smaller product size, a highly desirable feature. CRT replacement requires a 10W to 20W inverter to drive the CCFL (cold cathode fluorescent lamp) that illuminates the LCD. Additionally, the inverter must provide the wide dimming range associated with CRTs, and it must have safety features to prevent catastrophic failures...
A useful operation for the cars is delayed extinguishing internal lighting cabin of passengers, after close some door of car. Certain cars allocate this operation from their constructor. Oldest sure do not allocate such operation. This delay makes this circuit. In the scheme appears the delay circuit as well as a typical circuit of connections of lamp L1, usually 12V 10W, with the switch S1 choice of lamp operation. In place A the lamp L1 remains continuously turned on,.....
You can use this powerfull amplifier in any small audio project. It is very small (6.5 x 4.5 cm).It outputs 10W and uses a 9V battery...
..
This project and your efforts will provide you with a 0.55...3 watt input to easily 10 watt output. The two linear amplifiers are ment for use with QRP SSB/CW/FM/AM transmitters on the amateur bands 15 and 17 meters can be powered from a 12 volt DC supply. The design is a good balance between output power, physical size. The completed amplifier will reward the builder with a clean, more powerful output signal for a QRP rig when radio conditions become marginal...
This circuit was designed to provide that continuous light lamps already wired into a circuit, become flashing. Simply insert the circuit between existing lamp and negative supply. Especially suited for car or panel pilot lights, this device can drive lamps up to 10W. Ideal to operate 3 to 24V DC existing on-circuit lamps. LED operation is also possible...
The bass lift curve can reach a maximum of +16.4dB @ 50Hz. In any case, even when the bass control is rotated fully counterclockwise, the amplifier frequency response shows a gentle raising curve: +0.8dB @ 400Hz, +4.7dB @ 100Hz and +6dB @ 50Hz (referred to 1KHz). As amplifiers of this kind are frequently used to drive small loudspeaker cabinets, the bass frequency range is rather sacrificed. Therefore a bass-boost control was inserted in the feedback loop of the amplifier,.....
First set C12 and C14 to the middle and centre pin of P1 to the ground. After carefully mounting all parts and using as short as possible connections between the parts, gently add voltage to the amplifier while checking the current. The only current you should see is a the liddle idle current of T1 (and LED D6 if connected). Increase the voltage to 12 volts. Check current again. It should (at this stage) be lower then +/- 20mA...
This is a simple peak limiter - performance is quite respectable, and it can be used with conventional amps using bipolar transistors, MOSFETs, valves, etc, as well as BTL (Bridge Tied Load) amplifiers in car audio systems or for hi-fi. It will work with any amplifier from about 10W up to the highest power you are likely to encounter...
A control circuit at the lamps` site reacts selectively to the polarity of this dc pulse and controls the power to the two lamps. The required power rating of the two zener diodes depends on the load current. The short duration and low duty cycle of the activation are helpful. The 1N2976 diodes in Figure 1 are rated for continuous dissipation of 10W...
High Quality, very simple design. No preamplifier required. This design is based on the 18 Watt Audio Amplifier, and was developed mainly to satisfy the requests of correspondents unable to locate the TLE2141C chip. It uses the widespread NE5532 Dual IC but, obviously, its power output will be comprised in the 9.5 - 11.5W range, as the supply rails cannot exceed ±18V...
The whole Construction : You can call the transceiver like this as "OZL type". Characteristics of the "OZL type" are as follows. 1. Single conversion super. 2. Using two DBM-s as modulator and converter. 3. Modulator DBM is used as demodulator in receiving time. 4. All amplifiers are used in transmitting and receiving time. 5. Case is second use of my failed or useless machine.(This time I used my useless old 10W 7MHz transmitter.) 6. All decals are done with the.....
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
