Pulses from the distributor points are passed through a current limiting resistor, rectified, and clipped at 4 volts. Via Q1 and the diode pump, a dc voltage proportional to engine rpm is presented to RV1; the sharp transfer characteristic of a CMOS gate, assisted by feedback, is used to enable the oscillator formed by the remaining half of the 4011..
ICla and b are biased into the linear regions by R3 and R4. (ICI must be 4011A)..
The circuit uses four NAND gates of a 4011 package. In each oscillator, while one gate is configured as a straightforward inverter, the other has one input that can act as a control input. Oscillator action is inhibited if this input is held low. The first oscillator (ICla and IClb) has this input tied low via a high value resistor (Rl) that acts as a sensitivity control. Thus this oscillator will be disableduntil the control input is taken high. Any moisture bridging the.....
Two gates of a 4011 arc used as a comparator. When the resistance of R4 decreases the voltage at pin 1 and 2 increases, producing a logic zero at pin 3, causing pin 4 to go high and activating the LED. R3 is calibrated in light units, or seconds exposure time. To calibrate, set pot R3 so as to just be on the LED ON/OFF threshold. With a light level that is suitable to correctly expose a photographic print,..
IC1a, IC1b, and IC1c of the quad two-input NAND gate 4011 are connected as an astable multivibrator; IC1d is connected as an inverter. Terminals 3 and 11 of the 4011 produce square waves with opposite phases. The square waves, eP, at the output of IC1a, passing through differentiator C4R13, then form positive and negative pulses, e,. The dual op amps of the LM358 are used as two gated amplifiers for singles e1 and e2 and fed through terminals 2 and 6, to be displayed.....
The generator described here is intended for multiburst signal square waveform generation and can be used as a device for characterizing the response of TV monitor amplifiers as shown. The circuit is an RC oscillator with NAND gates (IC4-4011), with its capacitor C changed periodically by means of bilateral switches (IC2, IC3-4016). The control inputs of bilateral switches are driven by the outputs of a counter/decoder (IC1-4017) the operation of which is determined by.....
This is a simple Photo-sensing circuit. When light hits the photo-transistor, triggers the 4011 that drives a loudspeaker. ..
The A/B Switch circuit consists of three ICs and a handful of resistors. Two gates from a 4011 quad 2-input N..
This protection circuit is inserted between the reset switch and the motherboard. The earth connection of th..
This battery saver circuit can automatically turn off a small piece of test equipment after a desired period of time, allowing you to leave your shop worry free.This circuit uses a CD4011IC to act as a simple timer. One section acts as an RC discharge timer (pin 7). This causes ils output to go low, holding the three other outputs high acting as a 9-V source...
A two-tone generator that is alternately switched ON provides a high/low output as might be heard from a traffic vehicle like a police car or ambulance. IC1, CD4011, quad 2-input NAND gate is a two-tone oscillator in which each side, pins 1 through 7 and 8 through 13 set the tone frequencies. Changing the values of C9 and C] determines the high/low tones. The outout frequencies are coupled to IC2, CD4011, of which one side (pins 1 through 6) acts as a buffer. The buffer.....
By judging the rate at which a particular LED flashes, you`ll be able to estimate the resistance. The circuit consists of two IC`s (1 4011 CMOS quad 2-input, NAND gate, Ul; and a 4024 binary counter, U2), seven LEDs, and a handful of additional .components. All of the gates in Ul are wired as inverters. Two of the inverters (Ul-a and Ul-b) comprise an astable-multivibrator (free-running oscillator) circuit, whose operating frequency depends on the amount of resistance.....
The circuit uses a 4011 CMOS NAND gate, a pair of diodes and an NPN power transistor to provide a variable duty-cycle dc source. Adjusting the speed control varies the average voltage applied to the motor. The peak voltage, however, is not changed. This pulse power is effective at very low speeds, constantly kicking the motor along..
The detector uses three sections of an L144 and a DC4011 type CMOS NAND gate to make a very low power voltage monitor. If the input voltage, Vin, is above Vhigh or below Vlow, the output will be a logical high. If (and only if) the input is between the limits will the output be low..
I don`t know why, but people like blinking lights. You see LED chasers everywhere, in TV shows (Knight Rider), movies, and store windows. This schematic is my version of a simple 10 LED chaser. There is no 555 timer used because at my local electronics store they are over $4 Cdn. Instead, an oscillator made up of two sections of a 4011 NAND gate is employed. This chip is very inexpensive and extremely common...
The LTC®4010 and LTC4011 are NiCd/NiMH battery chargers that simplify Nickel-based battery charger design and include power control and charge termination for fast charging up to 16 series-connected cells using a synchronous buck topology. The LTC4011 provides a full feature set in a 20-lead TSSOP while the LTC4010 comes in a 16-lead TSSOP...
This frequency doubler uses one CMOS quad, two input NAND gate package type 4011. The frequency doubler proper consists of an inverter IC1B, two differentiating networks R1/C1, R2/C2 and NAND gate IC1A, IC1C and IC1D function as input and output buffers. In Fig.2 exist the pulses in different points of circuit...
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
