There are still neighbors that keep annoying you by having loud the TV or the radio? Well I have you the solution. In fact all neighborhood will face your jamming waves at their TVs and radios, so be careful. This Jammer is the improved version of the old "TV and FM jammer schematic" with the difference of much higher power. Many of you where asking for a stronger and wider effect but to be as portable as can be. Looking at the schematic you can see that, only the.....
An audio source, like a mixer, preamp, EQ, or a recorder, is fed to the input of the Electronic Crossover Circuit. This signal is either AC or coupling, depending on the setting of switch 51, the non-inverting input of buffer amplifier Ul-a, a section of a quad BIFET, low amp TL074 noise made by Texas Instruments op. This stage has a gain of 2, and its output is distributed to both a low pass filter made by R4, R5, C2, C3, and Uld op-amp, and a high-pass filter made by R6,.....
Due to the low duty cycle of flashing LED, the average current drain is 1 mA or less. The NE555 will trigger the LED on when the monitored voltage falls to 12 volts..
With the values shown the circuit generates a 2-MHz symmetrical square wave. Changing capacitors Cl and C2 to 0.01 µ¥ results in a frequency of 500 Hz. ..
This converter uses a low-pass filter instead of the usual tuned circuit so the only tuning required is with the receiver. The dual-gate MOSFET and FET used in the mixer and oscillator aren"t critical. Any crystal having a frequency compatible with the receiver tuning range may be used. For example, with a 3500 kHz crystal, 3500 kHz on the receiver dial corresponds to zero kHz; 3600 to 100 kHz; 3700 to 200 kHz, etc..
By making Rt variable it is possible to alter the operating frequency over a 100 to 1 range..
A phase-controlled dimmer delays the triac turn-on to a selected point in each successive ac half cycle. Use this circuit only for incandescent lamps, heaters, soldering irons,..
This circuit switch slowly on and off the internal lights in a car. The delaying time can be adjusted changing the values of the 10k, 4M7 resistors and capacitor...
The step size of the converter is variable by selection of the high order data bits. The first DAC, A, has a stable reference current supplied via the 10.24 V reference IC and Rl. R2 provides bias cancellation. As shown, only the first 4 MSB inputs are used, giving a step size of 225/256 2.048/16 = 0.127 mA. This current supplies the reference for DAC whose step size is then 0.1275/256 = 0.498 µ. Complementary voltage outputs are available for unipolar output and.....
The circuit"s frequency of oscillation is/= 2.8/ [C1 x (R1 + R2)]. Using the values shown, the output frequency can be varied from 60 Hz to 20 kHz by rotating potentiometer R2. A portion of IC1"s output voltage is fed to its noninverting input at pin 3. The voltage serves as a reference for capacitor Cl, which is connected to the noninverting input at pin 2 of the IC. ..
A high-gain amplifier using a UA741 is used to sense relative voltage drop in a conductor, and therefore current i..
The rectifier input is tied to the input. This makes gain inversely proportional to input level so that a 20-dB drop in input level will produce a 20-dB increase in gain. The output will remain fixed at a constant level. The circuit will maintain an output level of 1 dB for an input range of +14 to -43 dB at 1 kHz...
This circuit uses a stereo amplifier IC in a 14-pin DIL package that requires very few external components to make a complete 2 Watt per channel power amplifier. ..
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
