- Home /
- Search about Fm amplification circuit
Page 618 about Fm amplification circuit | |
Total Found: 19775 |
-
This circuit sends MIDI program changes. It's useful as a guitar pedalboard remote...
-
It is well know that pests like rats, mice etc are repelled by ultrasonic frequency in the range of 30 kHz to 50 kHz. Human beings can't hear these high-frequency sounds. Unfortunately, all pests do not react at the same ultrasonic frequency. While some....
-
Power input is to a 7805 5 volt regulator. A pair of LEDs is connected between the 5 volt supply and ground, with current limiting resistors in series and one pin on the AT90S2313 shunts the current through one LED or the other. When one LED is on, the....
-
The entire circuit is powered from a very simple regulated +-15V power supply, that is able to deliver about 2 A continuous duty, and at least 6 A on musical peaks. Two three-terminal regulators with power transistors wrapped around them do the regulating....
-
This circuit, enclosed into a small box, is placed in the fridge near the lamp (if any) or the opening. With the door closed the interior of the fridge is in the dark, the photo resistor R2 presents a high resistance (>200K) thus clamping IC1 by holding....
-
As you can see, there is only one regulated 12 volt supply operating the entire circuit. I was able to do this simply by AC coupling the received signal to U3 via C10. This allowed me to adjust the offset within an operating window. By using a tantalum....
-
Using a standard PLL circuit, such as the CMOS 4046B with some passive components, is a well-known way to design a clock multiplier. Unfortunately, using a PLL in a digital circuit has two disadvantages: It takes a long time for the circuit to reach a stable....
-
The circuit presented here can be used for connecting two telephones in parallel and also as a 2-line intercom. Usually a single telephone is connected to a telephone line. If another telephone is required at some distance, a parallel line is taken for....
-
This is a simple single-zone burglar alarm circuit. Its features include automatic Exit and Entry delays and a timed Bell/Siren Cut-Off. It`s easy to use. First check that the building is secure and that the green LED is lit. Then move SW1 to the "set"....
-
This circuit will generate a smaller DC output voltage from a larger DC input voltage.It is quick and simple to make and by changing the value of the zener diode, the circuit can be universally adapted to provide other output voltages.The circuit and all....
-
This circuit gives out an alarm when its sensor is wetted by water. A 555 astable multivibrator is used here which gives a tone of about 1kHz upon detecting water. The sensor when wetted by water completes the circuit and makes the 555 oscillate at about....
-
This circuit is a simple two transistor (2N2222) FM transmitter. No license is required for this transmitter according to FCC regulations regarding wireless microphones. If powered by a 9 volt battery and used with an antenna no longer than 12 inches, the....
-
The guitar input stage is a class A amplifier with adjustable bias. A 2N3906 PNP tranistor is used for a low noise design on this stage. The output of the preamp stage is sent to three places: the output mixer amp, the reverb driver amp, and the input....
-
The "LCD2LPT with Lirc" circuit is the compilation of two circuits found on the net on a single board. The first is LCD to LPT interface and the second an IR remote control interface using http://www.lirc.org program. The main circuit for LCD connection to....
-
The LT®3465 white LED driver is ideal for backlight circuits in small, battery-powered portable devices such as cellular phones, PDAs and digital cameras. The LT3465 includes important features such as automatic soft-start to prevent large inrush....
-
A number of single-chip VGAs variable-gain amplifiers are available today. Unfortunately, they all have drawbacks, such as high noise, 55V limit, low input impedance, or nonlinear gain/frequency characteristics. The circuit in Figure 1 is a 16-step,....
-
The circuit was designed to work with an audio power amplifier which operated off +18v-0v-18v power rails. The actual voltage used is not too critical except that the feedback is referred to the LED chain which itself is anchored to a +12v rail, hence the....
-
This timer was designed for people wanting to get tanned but at the same time wishing to avoid an excessive exposure to sunlight. A Rotary Switch sets the timer according to six classified Photo-types ...
-
This Intercom is powered by two 9volt batteries and uses only current when the Intercom is used. Both units are connected via a two-wire little cable or simply two wires (dotted lines). The loud speakers act both as loudspeaker and as a microphone.....
-
This is a very useful circuit for those who want to transform a stereo Power Amplifier, to mono, bridging two channels from him , reversing the phase of the one power amplifier [R] and the polarity, with these connections we can have 4X times the output....
-
Completed STK465 is an amplifier of acoustic frequencies that offers qualitative output, using minimal exterior elements. Substantially he is one of big completed force. Has a line pins and incorporated metal surface for adaptation in cooler. The provision....
-
This circuit warns the user against fire accidents. It relies on the smoke that is produced in the event of a fire. When this smoke passes between a bulb and an LDR, the amount of light falling on the LDR decreases. This causes the resistance of LDR to....
-
The standard circuit will display directly in Hz (1MHz max), and there is a seperate on board divider that will allow you to display directly in KHz (approx 40MHz max). Becuase the display reads directly in Hz or KHz there is no need for decimal point....
-
The synchronous oscillator (SO) and the coherent phase-locked synchronous oscillator (CPSO) are universal multifunctional networks that track, synchronize, and amplify as much as 80 dB; improve SNR by as much as 70 dB; and modulate AM, FM, and FSK signals...
-
When a processor-controlled device must operate reliably, designers often choose to periodically reset the processor rather than rely on a watchdog configuration. In low-power systems, this periodic-reset circuit can consume a large part of the system`s....
-
The circuit can be culled from the MCP2120 developer`s kit user`s guide. It is on page 51 of document DS51246A. If you don`t want to use an integrated transceiver, there is a circuit for you to build your own with a seperate ir led and detector. Make sure....
-
Many designers opinionate that NFB loop controlled amplifiers are inferior because they degrade the sound, and yet I wonder what it is that these individuals think they actually listen to ? The fact is that most vinyl waveforms and CD pits, as pressed into....
-
The tuned circuit consists of a variable capacitor and fixed air spaced coil. For the coil, I wound between 10 and 20 turns of wire on an empty tube of around 1.5 inches diameter. The turns were spaced so that the overall length was around 3 inches. The....
-
Two conventional amplifier stages built with SF215 transistors are linked by ceramic 10.7MHz IF filters, and followed by an FM demodulator built with a TBA120T i.c. Straight from the databook. Output goes via a 100k log potmeter (not shown) to the audio....
-
This circuit relies upon the extra high input impedance of a FET, and also demonstrates the gate terminals sensitivity to changes in voltage. The gate terminal here is left open circuit, connected only to the "probe" this being just a few inches of bare....
-
One of the most interesting projects to work with is that of a synthesizer that can accurately gnerate desired frequencies. This synthesizer uses just three CMOS chips and one PNP transistor. It is a fact that the transistor may be the hardest component to....