This small circuit is a Linear amplifier for driving small UHF TV transmitters. Its gain is 7dB and can amplify a signal between 450-800 MHz. You can drive the circuit with 1 to 1,5 Watts signal. Better use double layer PCB with the second layer connected to earth. Use a stabilized power supply 25 volts and at least 5Amps...
This simple circuit gives 15 dB gain and can be mounted on 1 in 2PCB. Coil data is given for 85 to 95 MHz..
The continuity tester is for tracing wiring on printed circuit boards. It only consumes any appreciable power when the test leads are shorted, so no On/Off switch is used or required. The applied voltage at the test terminals is insufficient to turn on diodes or other semiconductors. Resistors below 50 ohms act as short circuit; above 100 ohms as open circuit. The circuit is a simple multivibrator—Tl and T2, which are switched on by transistor T3. The components in.....
This tester is for tracing wiring on Printed Circuit Boards. Resistors below 50 ohms act as a short circuit; above 100 ohms as an open circuit. The circuit is a simple multivibrator switched on by transistor T3. The components in the base of T3 are Dl, Rl, R2, and the test resistance...
This is the latest version of the Improved Infrared Receiver with Status LED which can control any desktop PC with an ordinary remote control. The project comes along with a small PCB in order to save space. It connects to the serial port as stated in the schematic and uses the freeware Girder (www.girder.nl) software together with Igor?s Plugin (www.cesko.host.sk/girderplugin.htm) to send commands to the PC. The potential uses of this device are countless (control MP3.....
This project (unlike most of the others) is based almost directly on the "typical application" circuit in the National Semiconductor specification sheet. As it turns out, the typical application circuit is not bad - would I go so far as to say hi-fi in the audiophile sense? Perhaps - with caveats. It has good noise and distortion figures, and is remarkably simple to build if you have the PCB...
# This version uses a double sided PCB. Dimensions are approximately the same as the original version. # Removed the second push button switch and components for the RS232 serial interface. # Added 22K resistor between MCLR input and Vdd. This eliminates the need for a jumper on the ICSP header in normal operation. (If you use a 12F683 you can omit this resistor as well since it has an internal pull-up) ..
This project`s purpose is to design a fully automated machine for drilling a printed circuit board, (PCB) blank at a minimum cost and with the minimum amount of custom machining. This low cost philosophy is achieved by adapting the existing mechanical assemblies from readily available computer peripherals and electronic measuring instruments. Drill data is transferred to the PCDrill from an Excellon drill file generated by a PCB CAD program running on a personal computer...
This device was designed to use two generic-patterned, pre-made, pre-drilled circuit boards that are available from Radio Shack, and other places. Parts consist of: two generic pre-etched and pre-drilled PCBs (printed circuit boards), 136 precision 1%, 1/2-Watt metal-film resistors (46 values), seven 1P10T rotary switches, seven knobs, two binding posts, wire, solder, drilled cast-aluminum or plastic case (7.5"x4.3"x2.4"), panel markings, and rubber feet...
This project is intended for controlling mains powered disco lighting, although there are many other possible uses for controlling almost any mains appliance. It will control five seperate channels at up to 3 Amp per channel. This could be increased by designing another PCB with wider tracks than the PCB included with this design. I could have used relays to control my lights, but triacs seemed like a more sensible solution as they react quicker and are totally silent as.....
This is the construction guide for the 5301 wideband fuel mixture display kit. The 5301 is the Tech Edge version (rather than the Jaycar version) of the modified Silicon Chip FMD design, and it features, compared to the original kit, double sided PCBs a new front panel design, in-built RS232 output and superbright GaAlAs 7 segment LEDs The 5301 uses the same version 1.1 software as the 5300 and, unless noted otherwise, is known elsewhere on this web site as the 5300 unit.....
The amplifier drives a pair of loudspeakers using two LM3876 integrated power amp ICs (50 watts per channel), or a pair of headphones via a Meier crossfeed filter and an OPA2134 dual opamp. It provides four switchable line level inputs, and an unbuffered line level output for recording purposes. The design uses readily available good quality components, and is based around four separate PCBs; one for each power amp channel, one for the power supply board, and one for the.....
The synth stack consists of the following modules, a combination of Oakley Sound pcbs mounted on 19" panels and home-made custom units in 19" rack mounted boxes. Audio + Design Ambisonic Pan-Rotate Unit. Passive attenuator and input panel for A&D Ambisonic Pan-Rotate unit, B-format switch for pre and post record monitoring. A + D UHJ Encoder/Transcoder. A + D B Format Converter (not used). 4 X Stage Line 50W stereo amplifiers. Ye Olde 120MHz AMD P5 PC containing a Terratec.....
Build your own a personal writer for programming HEX code into Flash based microcontroller AT89C2051(2k) and AT89C4051(4k). Simple hardware and Easy use software in DOS and Window version. Single-side and double side PCB files included...
The following page outlines detail information on how to step by step design a Simple Heat Sensor Circuit. This circuit design utilized LM741 as the operational amplifier...
The Game Boy Camera uses a cheap CMOS image sensor with a resolution of 128*123 and an analogue monochrome output. This page shows how to connect it to a standard non-bidirectional, non-ECP, non-EPP PC parallel port, with 5 bits per pixel, compared to the Game Boy`s 2 bits dithered. The circuit described here uses only the small PCB in the swivelling part of the camera, which contains the AR chip, lens assembly and pretty much nothing else...
The project we have chosen as our example is an RS232 to RS485 converter. This is a often needed device which can demonstrate a lot of principles of circuit design, and hopefully the finished project will be useful to some people, just as it stands. Without meaning to confuse the issue, we also have available a second, more up-to-date 232-to-485 converter. This project demonstrates how we produce an electronic project using one particular PCB CAD package. Our business is.....
P-CAD is the complete design solution for the PCB professional. Whether it`s developing high-speed board solutions, integrating large BGA devices into your design flows or dealing with complex signal integrity issues and high density PCB layouts....
The device comprises two parts: LED control board and LED display board. The two PCBs are designed to fit together one behind the other using two sets of dual row connectors and 4 spacers. One of this connector is used for the electrical connections, while the other is only used as a mechanical connecting element. The core of the device is microcontroller PIC18F252 (U9). It controls all the functions of the device, generates the overall algorithm to control the LED matrix......
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
