To generate regulated ± 5-V supplies from a pair of dry batteries, the circuit of Fig. 1 is commonly used. In order to give protection from inadvertent reverse connection of a battery, a diode in series with each battery would produce an unacceptable voltage drop. The more effective approach is to fit diodes Dl and D2 as shown in Fig. 2, in parallel with each battery. When the supply is switched off, there is the risk of a reverse bias being applied across the.....
Due to the low duty cycle of flashing LED, the average current drain is 1 mA or less. The NE555 will trigger the LED on when the monitored voltage falls to 12 volts..
A flashing light of high brightness and short duty cycle is often desired to provide maximum visibility and battery life. This necessitates using an output transistor, which can supply the cold filament surge current of the lamp while maintaining a low saturation voltage. ..
This transmitter can be used for transmitter hunts, for remote key finding, or for radio telemetry in model rockets. It can be tuned to the two meter band or other VHF bands by charging Cl and Ll. 11 is four turns of #20 enameled wire airwound, 0.25 inch in diameter (use a drill bit), 0.2 inch long, centertapped. The antenna can be 18 inches of any type of wire. IC2 functions as an audio oscillator that is turned on and off by IC1 about once per second. ..
This unit is easily tunable and stable, consumes little power, and costs less than other types of oscillators tlmt operate at the same frequencies. This unusual combination of features is made possible by a design concept that includes operation of the transistor well beyond the 3 dB frequency of its currentversus- frequency curve. The concept takes advantage of newly available crystals that resonate at frequencies up to about 1 GHz. ..
Teledyne Semiconductor"s Type TSC9402 is a versatile IC. Not only can it convert voltage into frequency, but al..
A phase-controlled dimmer delays the triac turn-on to a selected point in each successive ac half cycle. Use this circuit only for incandescent lamps, heaters, soldering irons,..
The step size of the converter is variable by selection of the high order data bits. The first DAC, A, has a stable reference current supplied via the 10.24 V reference IC and Rl. R2 provides bias cancellation. As shown, only the first 4 MSB inputs are used, giving a step size of 225/256 2.048/16 = 0.127 mA. This current supplies the reference for DAC whose step size is then 0.1275/256 = 0.498 µ. Complementary voltage outputs are available for unipolar output and.....
A high-gain amplifier using a UA741 is used to sense relative voltage drop in a conductor, and therefore current i..
In this circuit, audio fed to the control channel is amplified and rectified by Dl and D2. This dc level activates LED D3 via Q2. The light from D3 causes R9, a light-dependent resistor to decrease resistance. As Rll (audio gain) is set higher, more audio is present at the output of Ql. Audio fed into J2 is shunted to ground via R9 and less of this audio appears at J3...
The circuit consists of two basic circuits, the oscillator and the detector. The oscillator uses an FET in a Colpitts configuration. The energy circulating in the oscillator tank is coupled through C4 to the detector circuit, where a small diode (D2) rectifies it, feeding a dc voltage to the Darlington pair (Q2, A3) controlled by the sensitivity control (R3). Any small variations in the bias of the amplifier will cause large variations of current through the LED indicator.....
If we are speaking about professional Cell phone Jammers we are talking about this schematic below. First off all you should be very careful how to use this device. Its fully illegal and so the purpose I post this Circuit is only for educational and testing reasons. This type of device is being used by security for VIPS, specially at their limousines to avoid bomb triggering while the car passes from the target cell phone-bomb. Offcourse there are those who use it to make.....
At this circuit the SSM2044 IC is used, a 4 pole voltage controlled filter designed for electronic music applications. On-chip voltage control of resonance allows direct and easy interfacing with programmers and controllers. The IC features extended control range, low noise, and high control rejection. The filter can also be used as a low distortion sinewave oscillator...
The meter reading is directlyjproportiona! to the logarithm of the input light power. The logarithmic circuit behavior arises from the nonlineardiode pnjunction current/voltage relationship..
Ql and Q2 constitute a simple, high-speed FET input buffer. Ql functions as a source follower, with the Q2 current source load setting the drain-source channel current. The LT1010 buffer provides output drive capability for cables or whatever load is required. Normally, this open-loop configuration would be quite drifty because there is no de feedback. The LTC1052 contributes this function to stabilize the circuit. It does this by comparing the filtered circuit output.....
The logic probe can indicate four input states, as follows: floating input—all LEDs off..
Inserting two 1-MO resistors, R1 and R2, in the output stage of one of the circuit"s inverters limits the current needed by the oscillator tone more than a few pA. This circuit includes a CD4007 package, which has three CMOS inverters. It forms a standard three-inverter oscillator. Resistors R1 and R2, in series with separate drains on inverter pins 8 and 13, limit the oscillator"s supply current. Capacitor C1 and resistors R5 set the off time of the oscillator, C1; R6.....
This device will tell a driver if his lights should be on and will wam him if the outside temperature is nearing zero by lighting a LED and sounding a buzzer9 VR1 adjusts sensitivity and LDR should be well protected..
Using an intersil ICL 7106 A/D converter chip and an LED display module, this gauge uses a Sensym Corp. pressure tra..
An LM317 voltage regulator is configured as a constant-current source. It is used to supply the 50 mA charging current to S01-S06, an array of AA-cell battery holders. Each of the battery holders is wired in series with an LED and its associated shunt resistor. When the battery holder contains a battery, the LED glows during charging. Each battery holder/LED combination is paralleled by a 5.1-volt Zener diode. If the battery holder is empty, the Zener conducts the current.....
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
