- Home /
- Search about flip-flop
Page 4 about flip-flop | |
Total Found: 171 |
-
This is basically 4 nearly identical debounced switches. The 2 resistors and one capacity at the input of each Schmitt trigger are used for debouncing the switches. The output is then fed into a D-type flip-flop which uses feedback to change the state (LOW....
-
The automatic sprinkler controller circuit is composed of the clock timing controller, monostable flip-flop, bistable flip flop, electronic switch, self-excited multivibrator, counter, solenoid valve control circuit and power supply circuit, and the circuit....
-
This circuit is a bistable multivibrator, or flip-flop. Click on the "set" input at lower left to bring the output high (5V). Click on the "reset" input at lower right to bring the output low (ground). The transistors are cross-coupled in such a way that the....
-
Light emitted by Xenon flash tube is transmitted to phototransistor MRD300 through optical fiber. Sensitive current is amplified to triggering a string of thyristors simultaneously. Therefore, high voltage of 6000V is set on loader R. This optical trigger....
-
When the push button is pressed, a clock pulse appears on the CLK input of flip-flop IC1b. The output then toggles and the LEDs turn off. At the same time IC1a is reset, which silences the buzzer. If you press the button again, the LEDs will turn on since....
-
The function of this circuit is to sound a buzzer, or, optionally, actuate a relay, when a certain moisture level is detected between a pair of probes. The circuit has a memory` in the form of a flip-flop, IC1a-IC1b, which enables or disables a tone....
-
Here we are going to discuss about an Asynchronous 4 Bit Binary Up Counter, a circuit made up of several J-K flip-flops cascaded to generate four bits counting sequence. An up counter is basically a digital counting circuit which counts up in an incremental....
-
Sixteenth street control circuit composed of the second decoding output control circuit. Connect an bistable circuit that composed of dual D flip-flop CD4013 to every output terminal of the sixteen decoding. Connect a DC relay on each output terminals of....
-
A very useful, easy and interesting project of a flip flop relay circuit using a 555 IC. The circuit will continously flip flop or on and off two relays one by one. ....
-
This flip-flop circuit is a free running/astable multivibrator one, with bases and collector of both emitter biased transistor are directly coupled to each other. Switching action is supported by means of capacitor in each emitter circuit. This configuration....
-
Next to the CLOCK input shows that it is edge-triggered, that is, it responds to sudden changes in voltage, but not to slow changes or to steady logic levels. The CLOCK input of the 4013 D-type bistable is rising-edge triggered, meaning that it responds only....
-
In this circuit 4017 CMOS decade counter can be used to build a timer circuit. Push-button S1 will discharge capacitor C1 through resistor R2 ....
-
The IR photo transistor Q1 (Radio Shack 276-145A) or similar is connected to the set input (pin 6). The photo transistor should be shielded from direct light so that the voltage at the set input (pin 6) is less than 1 volt under ambient conditions and moves....
-
The IR photo transistor Q1 (Radio Shack 276-145A) or similar is connected to the set input (pin 6). The photo transistor should be shielded from direct light so that the voltage at the set input (pin 6) is less than 1 volt under ambient conditions and moves....
-
This circuit shows how a 4017 CMOS decade counter can be used to build a timer circuit. Push-button S1 will discharge capacitor C1 through resistor R2. When S1 is released, C1 will charge up through R1 causing a rising edge at the clock input of IC1. This....
-
The circuit below is similar to the one above but can be used with a laser pointer to toggle the relay rather than a push button. The IR photo transistor Q1 (Radio Shack 276-145A) or similar is connected to the set input (pin 6). The photo transistor should....
-
This flip-flop circuit is a free running/astable multivibrator one, with bases and collector of both emitter biased transistor are directly coupled to each other. Switching action is supported by means of capacitor in each emitter circuit. This configuration....
-
A flip-flop that generates two unstable states (high-low) is called astable multivibrator, a fancy name for you to say it`s an oscillator. The very basic of....
-
A multivibrator is an electronic circuit used to implement a variety of simple two-state systems such as light emitting diodes, timers and flip-flops. The monostable multivibrator will create a condition: in which one of the states is stabl....
-
This approach can be demonstrated using the rather unusual semiconductor power flip-flop described here. A flip-flop is a toggling circuit with two stable switching states (bistable multivibrator). It maintains its output state even in the absence of an....
-
This particular timing circuit can be used to time one-shot events from a few seconds to a few hours. And in standby mode (ie, with RLY1 and LED1 off), its power consumption is very low. The heart of this circuit is a low-cost CMOS 4011 quad NAND gate, with....
-
Electronics Tutorial about Bistable Multivibrator also known as the Bistable Flip-Flop or Two-shot Multivibrator constructed from Transistors or Logic Gates....
-
A great collection of touch switch circuits. A touch switch is an electronic device that enables us to control a circuit by simply touching a sensor. The circuit as you can see from its diagram is very simple and only uses 8 components. The heart of the....
-
Author Jim Walker describes a very low cost analog delay line circuit using parts such as the LM311 comparator and 74HC74 D flip-flop...
-
The familiar astable flip-flop circuit is a handy configuration for making flashers or generating squarewaves. Here is a typical alternating LED flasher with the LEDs in the emitters instead of collectors as is normally done. (There is another good reason to....
-
I have it set up so that I get an out put signal that goes High for about 1/2 second, and then goes low for about 1.33 seconds. The problem is that....
-
Modern electronics is indispensable for every large model railroad system, and it provides a solution to almost every problem. Although ready-made product....
-
This add-on circuit enables remote switching on/off of battery-operated toy cars with the help of a TV/video remote control handset operating at 30 40 kHz. When the circuit is energised from a 6V battery, the decade counter CD4017 (IC2), which is configured....
-
It`s a typical AMV (Astable MultiVibrator) setup. The capacitor gets charged through both resistors until 2/3 Vcc is reached (internal comparator level). This sets a flip-flop which activates the Discharge output (DIS). Through DIS and the potentiometer, the....
-
4013 dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P- channel enhacement mode transistors. Each....
-
The NJM3772 is a stepper motor driverwhich circuit is especially developed for use in microstepping applications in conjunction with the matching dual DAC (Digital-to-Analog Converter) NJU39610. The NJM3772 contains a Clock oscillatorwhich is common for both....