There are still neighbors that keep annoying you by having loud the TV or the radio? Well I have you the solution. In fact all neighborhood will face your jamming waves at their TVs and radios, so be careful. This Jammer is the improved version of the old "TV and FM jammer schematic" with the difference of much higher power. Many of you where asking for a stronger and wider effect but to be as portable as can be. Looking at the schematic you can see that, only the.....
Although theIR region is free from radio interference, it is subject to interference from incandescent lamps, fluorescent lamps, stray reflections, and other sources. A simple way to overcome that problem is to create a carrier by chopping the IR radiation at a rate of 100 kHz. The audio then modulates the carrier by modulating the chopping rate. A receiver then detects the IR beam as a 100-kHz FM signal. ..
The search coil, CI and C2 form a tuned circuit for the oscillator which is tuned near the center of the broadcast band. Tune a portable radio to a station near the middle of the band, then tune C2 until a squeal is heard as the two signals mix to produce a beat (heterodyne) note. Metal near the search coil will detune the circuit slightly, changing the pitch of the squeal...
That RF Amplifier is for boosting small fm transmitters and bugs. It use two Philips 2N4427 and its power is about 1Watt. At the output you can drive any linear with BGY133 or BLY87 and so on. Its power supply has to give 500mA current at 12 Volts. More voltage can boost the distance but the transistors will be burned much earlier than usual.! In any case do not exceed the 15Volts. ..
The NE564 is used as an FM demodulator. The connections for operation at 5 V and 12 V are shown in Figures 21-4A and 21-4B. The input signal is ac coupled with the output signal being extracted at Pin 14. Loop filtering is provided by the capacitors at Pins 4 and 5 with additional filtering being provided by the capacitor at Pin 14. ..
This wideband antenna preamplifier has a gain of around 20 dB from 40 to 860 MHz, covering the entire VHF, FM, commercial, and UHF bands...
An LM311 comparator converts a small analog signal to a digital level for the DC4046 phase-locked loop, which is configured as a first-order FM demodulator. This demodulator works with a 50-kHz FM modulated input signal. It has applications in FM light beam receivers or in remote control applications...
This tracking transmitter consists of four distinct subassemblies; a free-running multivibrator, a transmit switch, an audio-tone generator, and an FM transmitter. The multivibrator (which produces a pulse width with a pulse separation of 1500 ms) is built around Ql and Q2. The multivibrator output is coupled through R5 to the base of Q3, whose emitter feeds Q4, ..
The control of both direction and of proportional motor speed is achieved by rotation of a single potentiometer. The motor driver is an SGS integrated circuit L293 which will drive up to 1 amp in either direction, depending on the logic state of input 1 and input 2 as per table. I/P 1 I/P 2 Function. High Low Motor turns one way. Low High Motor reverses. By applying a variable M/S ratio flip-flop to these inputs, both speed and direction will be controlled. With RV1 in its.....
In This application, a BA1404 is used to generate an FM MPX baseband signal. This modulates a crystal oscillator (Q3) via a dual varactor series modulator. ..
The vacuum tube is still alive and useful in some applications, as in this CW transmitter, The circuit was built in old-fashioned breadboard style on a wooden base. Old table radios are a good source of parts for this circuit. V3 is used as a ballast resistora 75- or 100- 5-W resistor could be substituted. LI is 15 turns of hookup wire on a form 2 long...
The design consists of an amplifier, a double-pole changeover switch and two loudspeakers: one for the master station and..
High quality, noise free, wireless FM transmitter/receiver operates over standard power lines. Complete system is suitable for high-quality transmission of speech or music, and will operate from any ac outlet anywhere on a one-acre home site. Frequency response is 20-20, 000 Hz and THD is under Transmission distance along a power line is at least adequate to include all outlets in and around a suburban home and yard..
Op amp Ul and its associated components comprise the 67-kHz bandpass filter. A twin-T network, comprised of four 1100-12 resistors and four 0.0022- capacitors, is connected in the feedback network of the op amp. That gives some gain at 67 kHz and heavy attenuation for frequencies above and below that frequency. An additional passive filter at the input to the twin-T network (containing a 220-pF capacitor and a 10,000- resistor) provides some additional roll-off for.....
This 49-MHz FM transmitter consists of an audio amplifier, a low-pass filter, three RF stages, and a regulated-dc power supply. The output is about 16 mW into a 50- load. This transmitter can be used in many 49-MHz applications, such as in a baby monitor, cordless telephone,..
A simple FM wireless microphone uses a single BC183C transistor as an audio amplifier. A 2N3565 can be substituted. ..
Use standard rf wiring precautions. The best speech clarity is obtained by using an electret microphone. ..
An op-amp IC (741) amplifies the audio signal from MIC1, and R12 controls its gain. Audio is fed to the oscillator circuit Q1 and related components. D2 is a varactor diode. Audio fed to D2 causes FM of the oscillator signal...
This tachometer lets you measure heartbeats, respiratory rates, and other low-frequency events that recur at intervals of 0.33 to 40.96 seconds. The circuit senses the period offm, computes the equivalent pulses per minute, and updates the LCD accordingly. Although the decimal readout equals 60 fm, the circuit doesn"t actually produce a frequency of 60 fm. ..
This circuit is configured for the 80m band. The 365-pF, broadcast-band variable capacitor should have a vernier drive with a six-to-one ratio, which makes tuning easier by separating the stations on the dial. A good antenna and ground are also recommended. ..
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
