There are still neighbors that keep annoying you by having loud the TV or the radio? Well I have you the solution. In fact all neighborhood will face your jamming waves at their TVs and radios, so be careful. This Jammer is the improved version of the old "TV and FM jammer schematic" with the difference of much higher power. Many of you where asking for a stronger and wider effect but to be as portable as can be. Looking at the schematic you can see that, only the.....
To generate regulated ± 5-V supplies from a pair of dry batteries, the circuit of Fig. 1 is commonly used. In order to give protection from inadvertent reverse connection of a battery, a diode in series with each battery would produce an unacceptable voltage drop. The more effective approach is to fit diodes Dl and D2 as shown in Fig. 2, in parallel with each battery. When the supply is switched off, there is the risk of a reverse bias being applied across the.....
Due to the low duty cycle of flashing LED, the average current drain is 1 mA or less. The NE555 will trigger the LED on when the monitored voltage falls to 12 volts..
A flashing light of high brightness and short duty cycle is often desired to provide maximum visibility and battery life. This necessitates using an output transistor, which can supply the cold filament surge current of the lamp while maintaining a low saturation voltage. ..
This transmitter can be used for transmitter hunts, for remote key finding, or for radio telemetry in model rockets. It can be tuned to the two meter band or other VHF bands by charging Cl and Ll. 11 is four turns of #20 enameled wire airwound, 0.25 inch in diameter (use a drill bit), 0.2 inch long, centertapped. The antenna can be 18 inches of any type of wire. IC2 functions as an audio oscillator that is turned on and off by IC1 about once per second. ..
This field strength meter consists of a tuned crystal detector producing a dc output voltage from a transmitted signal. The dc voltage is used to shift the frequency of a transmitter of 100-mW power operating at 1650 kHz. The frequency shift is proportional to the received field strength...
This unit is easily tunable and stable, consumes little power, and costs less than other types of oscillators tlmt operate at the same frequencies. This unusual combination of features is made possible by a design concept that includes operation of the transistor well beyond the 3 dB frequency of its currentversus- frequency curve. The concept takes advantage of newly available crystals that resonate at frequencies up to about 1 GHz. ..
When SI (sensor) is closed, power is applied to U2, a dual timer. After a time determined by C2, CI is ene..
Teledyne Semiconductor"s Type TSC9402 is a versatile IC. Not only can it convert voltage into frequency, but al..
The simple diode network can stabilize the voltage supplied to CMOS circuitry from a battery. D1 and D2 must have a c..
A phase-controlled dimmer delays the triac turn-on to a selected point in each successive ac half cycle. Use this circuit only for incandescent lamps, heaters, soldering irons,..
This low-power video transmitter is useful for R/C applications, surveillance, or amateur radio applications. Seven transistors are used in a crystal oscillator-multiplier RF power amplifier chain, and a high-level video modulator. A 9- to 14-Vdc supply is required. ..
The circuit furnishes an initial charging voltage of 2.5 V per cell at 25°C to rapidly charge a batt..
In this circuit, audio fed to the control channel is amplified and rectified by Dl and D2. This dc level activates LED D3 via Q2. The light from D3 causes R9, a light-dependent resistor to decrease resistance. As Rll (audio gain) is set higher, more audio is present at the output of Ql. Audio fed into J2 is shunted to ground via R9 and less of this audio appears at J3...
This circuit uses a stereo amplifier IC in a 14-pin DIL package that requires very few external components to make a complete 2 Watt per channel power amplifier. ..
The circuit consists of two basic circuits, the oscillator and the detector. The oscillator uses an FET in a Colpitts configuration. The energy circulating in the oscillator tank is coupled through C4 to the detector circuit, where a small diode (D2) rectifies it, feeding a dc voltage to the Darlington pair (Q2, A3) controlled by the sensitivity control (R3). Any small variations in the bias of the amplifier will cause large variations of current through the LED indicator.....
This type of reset pulse is ideally provided by this circuit. Because of the high input impedance of the Schmitt trigger, long reset pulse times may be achieved without the excess dissipation that results when both output devices are on simultaneously, as in an ordinary gate device (B). ..
This decoder will respond to a preselected 4-digit DTMF number. IC7 is a Radio Shack IC device (part #276-1303..
If we are speaking about professional Cell phone Jammers we are talking about this schematic below. First off all you should be very careful how to use this device. Its fully illegal and so the purpose I post this Circuit is only for educational and testing reasons. This type of device is being used by security for VIPS, specially at their limousines to avoid bomb triggering while the car passes from the target cell phone-bomb. Offcourse there are those who use it to make.....
At this circuit the SSM2044 IC is used, a 4 pole voltage controlled filter designed for electronic music applications. On-chip voltage control of resonance allows direct and easy interfacing with programmers and controllers. The IC features extended control range, low noise, and high control rejection. The filter can also be used as a low distortion sinewave oscillator...
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
