Gain increases by decades as the binary input decreases from 1,1 to 0,0. Minimum gain is 1 and maximum gain is 1000. ..
This self-biasing configuration is useful any time srnall changes in light level must be detected, for example, when monitoring very low flow rates by counting drops of fluid. In this bias method, the photodarlington is de bias stabilized by feedback from the collector, compensating for different photodarlington gains and LED outputs. The 10-I"F capacitor integrates the collector voltage feedback, and the 10-MO resistor provides a high base-source impedance to minimize.....
Large input-to-output voltage differentials, caused by wide input voltage variations, reduce a linear regulator`s efficiency and increase its power dissipation. A switching preregulator can reduce this power dissipation by minimizing the voltage drop across an adjustable linear regulator to a constant 1.5-V value. The circuit operates the LT1084 at slightly above its dropout voltage. To minimize power dissipation, a low-dropout linear regulator was chosen. The LT1084.....
This is a complete telephone bell replacement circuit with minimum external components with on-chip diode bridge and transient protection..
This circuit generates three supply voltages using a minimum of components. Diodes D2 and D3 perform full-wave rectification, alternately charging capacitor C2 on both halves of the ac cycle. On the other hand, diode D1 with capacitor C1, and diode D4 with capacitor C3 each perform half-wave rectification. The full-and half-wave rectification arrangement is satisfactory for modest supply currents drawn from -5 and +12-V regulators IC3 and IC2. ..
The preamplifier was designed to signal sources such as low-impedance moving coil cartridges (MC) on turntables high fidelity (and yet still there). The impedance of the amplifier is 100 W. To keep the noise levels low, three double-type transistors MAT03 SSM2220 or linked together to form a differential amplifier. Connecting this amp in front of an operand (OR27) is reduced to very low levels in noise input of the latter. The connections of the bases of the amplifier's.....
This circuit draws only 4 mA from a 5-V supply while driving a standard RS-232C receiver. The system clock drives a de-de converter that produces -3.4 V. The frequency can range from 0.5 to 8 MHz, but a range of 0.5 to 1 MHz will minimize power dissipation. The circuit output withstands direct shorts to ground or to either of the supplies ( ±12 V max). ..
While the battery is being charged, its voltage is measured at V. If the measured voltage is lower than the minimum the relay will be energized, that wiU connect the charger circuit. When the battery voltage runs over the maximum set point, the relay is deenergized and it will be held that way until the voltage decreases below the minimum when it will be connected again. ..
To display an rf signal, connect LI to the transmitter and points A and B to the vertical plates of the oscilloscope. Adjust LI for minimum SWR and C3 for the desired trace height on the CRT..
The LM39X4 acts as a LED-driving vol-tometer that has its basic maximum and minimum readings determined by the values of R2 and RV2. When correctly adjusted, the unit actually covers the 2 volt to 3 volt range, but it is made to read a supply voltage span of 10-10 volts to 15 volts by interposing potential divider R1-RV1 between the supply line and the pin-5 input terminal of the IC. The IC is configured to give a "dot" display, in which only one of the ten LEDs is.....
At the heart of the whistle swatch are a pair of tone detectors, each of which is built around an LM567 tone decoder, which are supported by a minimum of additional components. This whistle switch is designed to respond to only two or more occurrences of a specific tone, or sequence of tones, within a specified period to prevent false triggering. Depending on the relay used, various ac loads can be controlled. Microphone MICl picks up the sound and U2 amplifies the signal.....
This self-starting fixed-frequency oscillator circuit gives excellent frequency stability. R1 and C 1 comprise the frequency-determining network, while R2 provides the regenerative feedback. Diode D 1 enhances the stability by compensating for the difference between VaH and VsurrLY· ..
The circuit lowers the effective peak current of the output PUT, Q2. By allowing the capacitor to charge with high gate voltage and periodically lowering gate voltage, when Ql fires, the timing resistor can be a value which supplies a much lower current than IP. The triggering requirement here is that minimum charge to trigger flow through the timing resistor during the period of the Ql oscillator. ..
Most circuits that provide an electrical stimulus for research subjects are constant-voltage designs; this circuit is a constant-current design. Stimulator circuits must be isolated for two reasons: to ensure safety and to minimize interference. Isolated stimulators are essentially two-terminal devices; output currents can flow only between tbe two output terminals and can at no tiroe flow through any other path, such as the power ground. ..
This nonisolated, unregulated, minimum component converter fills the void between low-power zener regulation and the higher power use of a 60-Hz input transformer. It is intended for use where)"er a nonisolated supply can be used safely. The circuit operates~by conducting only during the low-voltage portion of the rectified sine wave. ..
This circuit is intended as a revolution control for small dc motors as fitted, for instance, in small electric drills (..
This two-chip receiver with minimum external component count has been designed for low-cost fiber optic applications to 100-M baud (50 MHz). The receiver is divided into pre-and postamplifier !Cs for increased stability. The preamplifier IC features low noise with a differential transresistance design. The postamplifier IC incorporates an auto-zeroed first stage with noise shaping, high-gain symmetrical-limiting amplifier, and a matched rise/fall time TTL output.....
The ATMEL, with family AVR, was consolidated in the field of microcontrollers. The microcontrollers are, providing fast core and a variety of peripherals. These features continue to occupy the attention of engineers and earn their preference. The developer will see, it accepts all models of the family of AVR. It is an excellent tool that stands out for its high performance and simplicity in handling. To develop, based on the record of AVR, the AVRDONGLE.PDF. If someone.....
This transmitter uses a 741 op amp as a high-gain audio amplifier, which is driven by a microphone. The output of the 741 is coupled to Ql, which serves as the driver for a LED. Potentiometer R1 is the amplifier`s gain control. Miniature trimmer resistor R6 permits adjustment of the base bias of Ql for best transmitter performance. Gain control R1 can be eliminated if CI and R2 are connected directly to pin 2 of the 741...
Most of you will certainly already installed on your computer one of the many software tools move freely from hand to hand and is suitable for programming the PIC 16C84. One of the most popular of this kind is the RIR02 of Silicon Studios. The circuit described below, is perhaps the simplest PIC programmer that can work seamlessly with the program RIR02. This guide allows RIR02 communication with the programmer, through the parallel port (Centronics). ..
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
