An audio source, like a mixer, preamp, EQ, or a recorder, is fed to the input of the Electronic Crossover Circuit. This signal is either AC or coupling, depending on the setting of switch 51, the non-inverting input of buffer amplifier Ul-a, a section of a quad BIFET, low amp TL074 noise made by Texas Instruments op. This stage has a gain of 2, and its output is distributed to both a low pass filter made by R4, R5, C2, C3, and Uld op-amp, and a high-pass filter made by R6,.....
To generate regulated ± 5-V supplies from a pair of dry batteries, the circuit of Fig. 1 is commonly used. In order to give protection from inadvertent reverse connection of a battery, a diode in series with each battery would produce an unacceptable voltage drop. The more effective approach is to fit diodes Dl and D2 as shown in Fig. 2, in parallel with each battery. When the supply is switched off, there is the risk of a reverse bias being applied across the.....
Precise, adjustable control of beats per minute from a largo of 18 to a frenzied, high presto of 500, These beats are produced acoustically through a speaker. A light flashes at the same rate. When SW1 is closed, CI begins to charge through Rl and R2. Cl will eventually reach a voltage at which the emitter of unijunction transistor is switched on, "dumping" the energy stored in Cl into an 8 ohm speaker. To produce a distinct "plop", brief pulses across T2 secondary drive.....
This circuit switch slowly on and off the internal lights in a car. The delaying time can be adjusted changing the values of the 10k, 4M7 resistors and capacitor...
This type of reset pulse is ideally provided by this circuit. Because of the high input impedance of the Schmitt trigger, long reset pulse times may be achieved without the excess dissipation that results when both output devices are on simultaneously, as in an ordinary gate device (B). ..
Input 1 is used as a gating period, during which a single rising edge on input 2 will cause a logic 1 output-any other number, indicating non-identical frequencies causes a logic 0 output. ICla converts input 1 to a narrow pulse which initializes IC2 which forms a two-stage shift register clocked by input 2. On the first edge of input 2 a logic 1 appears on the output of IC2b and for all subsequent inputs a logic 0 is present. At the end of the gating period this output is.....
Integrated circuit Ul (a 555 oscillator/timer) is wired as a conventional pulse generator. The frequency of the pulse generator is controlled by potentiometer Rll. Resistor R2 puts areasonable limit on the highest speed attainable. The output of the pulse generator is fed to the common clock input of U2, a 74C175 quad D-type flip-flop. Each flip-flop is configured so that its Q output is coupled to the D input of the subsequent flip-flop. Information on the D input of.....
The telephone-line tester consists of nothing more than a meter (that`s used to measure line voltage in the on- and off-hook state), three resistors (one of which is variable), a pushbutton switch, and a modular telephone connector...
This relatively simple, inexpensive circuit requiring one trimming operation can multiply or divide with a consistentaccuracy of greater than 1 part in 1,000. An inexpensive CMOS version of standard 555 timer chip T, in conjunction with low-drift LMll error amplifier A3, an inexpensive analog chopper switch SW, form a unique voltage-to-duty-cycle converter to produce the difficult transfer function necessary for accurate conversion. ..
Sounds are picked up by MIC1 and fed to the input of the first op amp. The signal is then fed to the input of second op amp Ulb, where it is boosted again by a factor of between 1 and 33, depending upon the setting of range switch Sl. With the range switch set in the A position, R6 is 1 K!:J and R7 is 33 K!:J, so that stage has a gain of 33. ..
This circuit will switch off the line supply to audio or video equipment if there has been no input signal for about 2 seconds. SI provides manual operation and S2 acts as a reset. This circuit allows for time to change a tape or compact disc. ..
This channel selector selects video and stereo audio from any one of three different sources. ..
The use of a switching transistor (like a 2N2222 or 2N3904) allows use of the CD4511B with a common-anode display. should be chosen to provide about 1 mA to drive Ql and Rr should provide enough current to drive the display...
The unit consists of rlamplifier Q1, local oscillatorQ2, and mixer Q3. The two bands are covered without a bandswitch by using an i-f or 3.5 MHz. The oscillator range is 7.5 to 14.5 MHz. Incoming signals from 4 to 11 MHz are mixed with the oscillator to produce the 3.5-MHz i-f. Signals from 11 to 18 MHz are mixed with the oscillator to also produce an i-f of 3.5 MHz. At any one oscillator frequency, the two incoming signals are 7 MHz apart. ..
If the tube is level with respect to gravity, the bubble resides in the tube"s center and the electrode resistances to common are identical. As the tube shifts away from level, the resistances increase and decrease proportionally. Transducers of this type must be excited with an ac waveform to avoid damage to the partially conductive liquid inside the tube. The level transducer is configured with a pair of 2-KO resistors to form a bridge. The required ac bridge.....
Large input-to-output voltage differentials, caused by wide input voltage variations, reduce a linear regulator`s efficiency and increase its power dissipation. A switching preregulator can reduce this power dissipation by minimizing the voltage drop across an adjustable linear regulator to a constant 1.5-V value. The circuit operates the LT1084 at slightly above its dropout voltage. To minimize power dissipation, a low-dropout linear regulator was chosen. The LT1084.....
A shows a typical LTC 1148 surface-mount, application providing 5 V at 2 A from an input voltage of 5.5 V to 13.5 V. The operating efficiency, shown in B, peaks at 97% and exceeds 90% from 10 mA to 2 A with a 10-V input. Ql and Q2 comprise the main switch and synchronous switch, respectively, and inductor current is measured via the voltage drop across the current shunt. /vgENSE is the key component used to set the output, current capability according to the formula/QUT.....
The meltdown is a magnet held to a small stand by ice. A reed switch is below the magnet..
Ql senses IR from heat sources, causes U1 to switch, activates optocopuler Ul, and triggers TR1. This contro..
When power is first applied, three things happen: the light-driving transistor (Ql) is switched on because of a low output from U2, pin 3; timer Ul begins its timing cycle, with the output (pin 3) going high, inhibiting U2`s trigger (pin 2) via D2; and charge current begins to move through R3 and R4 to CI.When Ul`s output goes low, the inhibiting bias on U2 pin 2 is removed, so U2 begins to oscillate, flashing the third light via Ql, at a rate determined by R8, R6, and.....
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
