Due to the low duty cycle of flashing LED, the average current drain is 1 mA or less. The NE555 will trigger the LED on when the monitored voltage falls to 12 volts..
This transmitter can be used for transmitter hunts, for remote key finding, or for radio telemetry in model rockets. It can be tuned to the two meter band or other VHF bands by charging Cl and Ll. 11 is four turns of #20 enameled wire airwound, 0.25 inch in diameter (use a drill bit), 0.2 inch long, centertapped. The antenna can be 18 inches of any type of wire. IC2 functions as an audio oscillator that is turned on and off by IC1 about once per second. ..
This field strength meter consists of a tuned crystal detector producing a dc output voltage from a transmitted signal. The dc voltage is used to shift the frequency of a transmitter of 100-mW power operating at 1650 kHz. The frequency shift is proportional to the received field strength...
This circuit has a flat response from 8Hz to 50 kHz at -3 db on tbe 10-mV range. ..
The circuit"s frequency of oscillation is/= 2.8/ [C1 x (R1 + R2)]. Using the values shown, the output frequency can be varied from 60 Hz to 20 kHz by rotating potentiometer R2. A portion of IC1"s output voltage is fed to its noninverting input at pin 3. The voltage serves as a reference for capacitor Cl, which is connected to the noninverting input at pin 2 of the IC. ..
A high-gain amplifier using a UA741 is used to sense relative voltage drop in a conductor, and therefore current i..
These two comparators are over- and under-voltage comparators. In Fig. 104-5(a), if Vm exceeds the reference voltage, t..
The circuit consists of two basic circuits, the oscillator and the detector. The oscillator uses an FET in a Colpitts configuration. The energy circulating in the oscillator tank is coupled through C4 to the detector circuit, where a small diode (D2) rectifies it, feeding a dc voltage to the Darlington pair (Q2, A3) controlled by the sensitivity control (R3). Any small variations in the bias of the amplifier will cause large variations of current through the LED indicator.....
The meter reading is directlyjproportiona! to the logarithm of the input light power. The logarithmic circuit behavior arises from the nonlineardiode pnjunction current/voltage relationship..
This circuit, instead of dividing by an integer, divides the input signal by +1/2. With the feedback connections ..
A circuit for multiplying the width of incoming pulses by a factor greater or less than unity is simple to build and has the feature that the multiplying factor can be selected by adjusting one potentiometer only. The multiplying factor is determined by setting the potentiometer in the feedback of a 741 amplifier. The input pulses of width r and repetition period is used to trigger a sawtooth generator at its rising edges to produce the waveform e2 having a peak value of.....
The circuit is built around a 741 general-purpose op amp that is configured as a voltage follower; with the components shown, the op amp has a voltage gain of one. The output of the 741 is used to drive a 50- meter movement. Potentiometer R7 is used to zero the meter and R6 sets the meter`s full-scale reading, Calibrating the meter is a snap. With no input applied to the circuit, set R6 to mid-position and adjust R7 to zero the meter. Once that is done, apply a positive.....
The first amplifier circuit is a bird phone. In this circuit, the electret mike (MIC1) is mounted in the neck of a large plastic funnel. The amplifier, built around an MC34119 (which is available from D.C. Electronics, P.O. Box 3203, Scottsdale, AZ 85271-3203; Tel. 800-467-7736, and elsewhere), is then placed outside of the funnel with the pickup facing a nearby bird feeder. The output of the amplifier is then connected to a 16- speaker. The amplifier`s voltage gain is.....
The logic input is applied to opto-isolators Ul and U2 with, respectively, npn and pnp emitter follower outputs. Dc balance is adjusted by potentiometer R2. The emitter followers drive the gates of Ql and Q2, the complementary TMOS pairs. With a ±12 V supply, the swing at the common source output point is about 12 V peak-to-peak. By adding a ± 18-V boost circuit, as shown, the output swing can approach the rail swing. ..
The positive and negative peak amplitude is controllable to an accuracy of about ± 0.01 V by a dc input. Also, the output frequency and symmetry are easily adjustable. The oscillator consists of an integrator and two comparators—one comparator sets the positive peak and the other the negative peak of the triangle wave. If R1 is replaced by a potentiometer, the frequency can be varied over at least a 10 to 1 range without affecting amplitude. Symmetry is also.....
A low-cost filament transformer provides a linear indication of the load current in an ac line. ..
Insulated-gate, field-effect transistor (IGFET), Q2 and silicon photo cell Zl form the heart of this circuit. Transformer T1 is an audio-output type, but it"s reversed in the circuit. A sudden flash from a photoflash unit detected by Zl sends a voltage pulse through the low-impedance winding of Tl via Rl. That voltage pulse is stepped-up in Tl"s 500-!l, primary winding before being rectified by Ql. Transistor Ql is used as a diode; its emitter lead was snipped off.....
Integrated circuit Ul (a 555 oscillator/timer) is wired as a conventional pulse generator. The frequency of the pulse generator is controlled by potentiometer Rll. Resistor R2 puts areasonable limit on the highest speed attainable. The output of the pulse generator is fed to the common clock input of U2, a 74C175 quad D-type flip-flop. Each flip-flop is configured so that its Q output is coupled to the D input of the subsequent flip-flop. Information on the D input of.....
The incoming RGB inputs are terminated with resistors Rl, R2, and R3 and potentiometers RVl, RV2, and RV3. These provide input impedances of approximately 75 0. The presets should be adjusted to provide a maximum input of 1 V pk-pk into the MC1377. The inputs are ac-coupled into the encoder; the large value capacitor is required for the 60 Hz field component. The Colpitts oscillator for the color burst is formed around pins 17 and 18. About 0.5 V pk-pk should appear.....
The circuit is built around a single 4093 quad 2-input NAND Schmitt trigger...
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
