The step size of the converter is variable by selection of the high order data bits. The first DAC, A, has a stable reference current supplied via the 10.24 V reference IC and Rl. R2 provides bias cancellation. As shown, only the first 4 MSB inputs are used, giving a step size of 225/256 2.048/16 = 0.127 mA. This current supplies the reference for DAC whose step size is then 0.1275/256 = 0.498 µ. Complementary voltage outputs are available for unipolar output and.....
The circuit furnishes an initial charging voltage of 2.5 V per cell at 25°C to rapidly charge a batt..
If we are speaking about professional Cell phone Jammers we are talking about this schematic below. First off all you should be very careful how to use this device. Its fully illegal and so the purpose I post this Circuit is only for educational and testing reasons. This type of device is being used by security for VIPS, specially at their limousines to avoid bomb triggering while the car passes from the target cell phone-bomb. Offcourse there are those who use it to make.....
An LM317 voltage regulator is configured as a constant-current source. It is used to supply the 50 mA charging current to S01-S06, an array of AA-cell battery holders. Each of the battery holders is wired in series with an LED and its associated shunt resistor. When the battery holder contains a battery, the LED glows during charging. Each battery holder/LED combination is paralleled by a 5.1-volt Zener diode. If the battery holder is empty, the Zener conducts the current.....
Insulated-gate, field-effect transistor (IGFET), Q2 and silicon photo cell Zl form the heart of this circuit. Transformer T1 is an audio-output type, but it"s reversed in the circuit. A sudden flash from a photoflash unit detected by Zl sends a voltage pulse through the low-impedance winding of Tl via Rl. That voltage pulse is stepped-up in Tl"s 500-!l, primary winding before being rectified by Ql. Transistor Ql is used as a diode; its emitter lead was snipped off.....
This electronic music maker uses an astable oscillator circuit that is controlled by a photocell. The light falling ..
The excellent characteristics for the track NPD8301 over its range of bias current, thereby improving common mode rejection. ..
When the light beam that falls in the CDS photocell is interrupted, transistor (EN3904) conducts thereby triggering SCR1 (CI06) and activating alarm bell. SI resets the SCR. The alarm bell should be a self-interrupting electromechanical type...
If a NiCad battery is discharged to a point at which the lowest capacity cell becomes fully discharged and reverses polarity, that cell will usually short internally and become unusable. To prevent this type of damage, this circuit detects a one-cell drop of 1.25 V and turns the load off before cell reversal can occur. Low-current zener or other voltage sensor Dl and resistors Rl and R2 establish a reference level for transistor Ql. ..
The LM101A provides gain and buffers the input from storage capacitor C2. R2 adds a zero in the open loop response to compensate for the pole caused by the switch resistance and C2, improving the closed-loop stability. R1 provides a slight delay in the digital drive to pins 1 and 9. C1 provides cancellation of coupled charge, keeping the sample-and-hold offset below 5 mV over the analog signal range of -10 through +10 V. ..
This self-starting fixed-frequency oscillator circuit gives excellent frequency stability. R1 and C 1 comprise the frequency-determining network, while R2 provides the regenerative feedback. Diode D 1 enhances the stability by compensating for the difference between VaH and VsurrLY· ..
This timer makes an excellent line receiver for control applications involving relatively slow electromechanical devices. ..
The solar cell is connected across the input of the FET (field-effect transistor), Ql, so that it will produce positive dc voltage to the gate when activated by light shining through the open shutter, decreasing the negative gate-source bias already established by the source resistor, and causes an increase in drain current. The drain voltage goes more negative which causes a decrease in Q2's base current. Q2's collector current decreases, and its collector voltage becomes.....
The heart of the electroscope is the two junction FETs Ql and Q2 connected in a balanced-bridge circuit. The gate input of Ql is connected to the wire pick-up antenna, while Q2"s gate is tied to the circuit"s common ground through R2. That type of bridge circuit offers excellent temperature stability; therefore, Ql is allowed to operate in an open-gate configuration. ..
The MC1596/MC1496 makes an excellent SSB product detector. This product detector has a sensitivity of 3 microvolts and a dynamic range of 90 dB when operating at an intermediate frequency of S MHz. The detector is broadband for the entire high frequency range. For operation at very low intermediate frequencies down to 50 kHz the 0 /aF capacitors on pins 7 and 8 should be increased to 1 /aF. Also, the output filter at pin 9 can be tailored to a specific intermediate.....
This limiter improves signal-to-noise ratio. It is connected between the detector output and the audio input (if high impedance) or at some relatively high-impedance section between two audio stages—preferably the low level stages.D1 and D2 can be any diode having relatively low forward resistance and very high back resistance. The circuit is excellent for receivers having bandwidths down to 2 or 3 kHz...
Provides remote control for ac-powered devices by using the beam of a flashlight as a magic wand. The important aspect of this gadget is that it remembers. Activate it once to apply power to a device and it stays on. Activate it a second time and power goes off and stays off..
The charger"s output voltage is adjustable and regulated, and has an adjustable constant-current charging circuit that makes it easy to use with most NiCad batteries. The charger can charge a single cell or a number of series-conoected cells up to a maximum of 18 V. Power transistors Ql and Q2 are conoected as series regulators to control the battery charger"s output voltage and charge-current rate. An LM317 adjustable voltage regulator supplies the drive signal to the.....
LDR1, a cadmium sulphide (CDS) photoresistive cell is used as the lower leg of a voltage divider between Vcc and ground. The timer terminals 2 and 6 are connected to the junction of the photocell and SENSITIVITY control Rl. The resistance of the photoresistive cell varies inversely as the light intensity; resistance is high when the illumination level is low; low in bright light. (The Radio Shack CDS cell 276-116 has a typically wide resistance range—about 3 megohms.....
The ATMEL, with family AVR, was consolidated in the field of microcontrollers. The microcontrollers are, providing fast core and a variety of peripherals. These features continue to occupy the attention of engineers and earn their preference. The developer will see, it accepts all models of the family of AVR. It is an excellent tool that stands out for its high performance and simplicity in handling. To develop, based on the record of AVR, the AVRDONGLE.PDF. If someone.....
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
