- Home /
- Search about transistors
Page 9 about transistors | |
Total Found: 916 |
-
Transistors T1 and T2 form the mic preamplifier. Resistor R1 gives the required bias for the mic condenser whilst preset VR1 works as gain control for adjusting its gain level. As a way to boost the audio power, the low-level audio output from the....
-
The simplest way to drive stepper motor having lower current rating is using ULN2003. The ULN2003 contains seven darlington transistors. The ULN2003 can pass upto 500mA per channel and has an internal voltage drop of about 1V when on. It also contains....
-
A gyrator is a circuit using active devices and transistors to simulate an inductor. In this case the gyrator is the transistor acting with R1, R3 and C2. It could just as easily be a unity gain op-amp (which gives superior performance). The circuit includes....
-
The three-tone electronic doorbell circuit consists of the coding triggered circuit, multi-tone generator and audio amplifier circuit, and it is shown in Figure 3-110. Coding trigger circuit is composed of the buttons Sl-S6, two four-input AND gate (DI, D2)....
-
A simple audio level meter or a Volume unit VU level meter circuit with diagram and schematic. This sound level meter is designed using transistors with a flat frequency response in the range of 20Hz to 50Khz....
-
This 15v variable power supply electronic project is designed using 2N3055 transistors. Output voltage of this variable power supply can be adjusted in the range between 1. 5 and 15 volts. This 2N3055 15v variable power supply can provide a maximum current....
-
The circuit of a FM Tracking Transmitter Circuit or Remote Control Transmitter Circuit is explained using 555 IC and and 2N4392 transistors....
-
A very good 1 watt fm transmitter circuit, very easy to build circuit. It has 4 transistors, one is a very stable oscillator, followed by a buffer stage to prevent frequency variation when you adjust the transmitter. Next is a resonance stage and the final....
-
-
This is the cheapest 150 Watt amplifier circuit you can get, I think. Based on two Darlington power transistors TIP 142 and TIP 147, this circuit can deliver a blasting 150 W Rms to a 4 Ohm speaker. Enough for you to get rocked, then try out this. TIP 147....
-
This simple circuit has helped me out on many occasions. It is able to check transistors, in the circuit, down to 40 ohms across the collector-base or base-emitter junctions. It can also check the output power transistors on amplifier circuits. Circuit....
-
This light sensor switch circuit allows the automatic connection of a lamp when the light is low (at nightfall) and will maintain the lamp ON for a certain period of time. From the moment that T4 and T5 are opened, relay`s LED start to light and powers the....
-
Using a single 7812 ic voltage regulator and multiple outboard pass transistors, this power supply can deliver output load currents of up to 30 amps. this circuit is Using a single 7812 IC voltage regulator and multiple outboard pass transistors, this power....
-
In this post, we shall be covering on how to construct a H-Bridge Motor Driver circuit using simple MOSFET`s and Transistors. The main feature of this H-Bridge is that the motor can be driven in both directions. AnH-bridgeis a circuitthat allows a voltage to....
-
Q1 and Q2, as well as T1, determine how much wattage the inverter can supply. With Q1, Q2=2N3055 and T1= 15 A, the inverter can supply about 300 watts. Larger transformers and more powerful transistors can be substituted for T1, Q1 and Q2 for more power. 2.....
-
The politely welcoming electronic doorbell circuit is composed of the trigger control circuit, audio amplifier output circuit, music circuit, voice delay control circuit, and it is shown in Figure 3-122. Trigger control circuit is composed of the doorbell....
-
2 meters 144MHz push pull amplifier wich can generate 200W, how does it sound ? Sounds delicious with 2 DV28120T transistors. DV28120T push pull amplifier....
-
The inverter circuit has a central component, the CMOS 4047, and converts a 12V DC voltage to 220V AC voltage. 4047 is utilised as a astable multivibrator. At pin 10 and 11 we find a rectangular symmetrically signal which is amplified by tow Darlington....
-
In this project you will build a coin toss circuit. It has three sections: a square-wave oscillator, a JK flip flop, and two LEDs (red & green). It uses CMOS digital ICs and MOSFET transistors. The schematic does not show the power and ground connections for....
-
Why have one resistor and transistor for each LED, instead of chaining the LEDs in series and controlling them with a single transistor which is controlled, in turn, by the arduino pin coming in through a single resistor I have no qualms about implementing....
-
This circuit generates a tone that sounds very similar to a siren. The generator part of the circuit is made of the combination of PNP and NPN transistors. Toghether, the two transistors build up a free runing multivibrator. If the C2 capacitor was connected....
-
LED flasher circuit here will flash a LED using only 1.5 volts ?supply voltage. Normally, to make any LED lamp works, you need more than 2 volts power supply..
-
This LED flasher circuit is a classic two transistor flip flop. This flasher circuit is very popular and it`s usually the first circuit to build when starting electronic circuit building hobby. Here is the schematic diagram of the famous LED flasher circuit:....
-
Circuit diagram is a simple but effective circuit intercom circuit is based entirely on transistors. Circuit diagram is based on three stages plus RC amplifier. When the pushbutton S2 is pressed, the amplifier cord around T1 ...
-
Flight Computer V1. 0: B1 PC Board U1 80C32 microprocessor U2 27C256-12 32Kx8 ROM - 120nS U3 74HC373 U4 LM340T-5 5v regulator (might be a 7805 part) U5 43C256-15 32Kx8 RAM - 150nS U6 74HC00 T1-T4 2N6045 or 2N6044 darlington output transistors Y1 11MHz....
-
A relay circuit to function as a DPDT toggle which is controlled by a momentary switch. I strive to keep my circuits simple with little or no integration (555`s, transistors, etc). The circuit is shown active or on mode. Half of RL1 and RL2 manipulate the....
-
The moderate power FM transmitter circuit employing two transistors.The voice signals picked by the microphone will be amplified by the transistor ....
-
A 12 Volt high current 20 Amp power supply. The output voltage is variable from 12. 2 Volt to 14. 4V so can be set for any device requiring voltage and current in that range. This PSU uses an LM723 as the regulator, 4 parallel connected outboard pass....
-
The power supply varies, and the circuit must operate on under 10uA of current (not counting charging the cap). It triggers an SCR every 10-30 seconds as long as the power supply is above 1. 8VDC, and must operate across a range of 1. 8 and 7. 0 VDC. The....
-
Connect a pic to an rn-41 bluetooth module. I`m not the person who designed the PCB, so I can`t answer exactly why the circuit is the way that it is instead of using the voltage divider used by some other people. Basically, the 5v logic from the pic is used....
-
The circuit is very simple and inexpensive. This is good thing because most commercial stepper motor controller ICs are quite expensive. This circuit is built from standard components and can easily be adapted to be controlled by a computer. If you use cheap....