At this circuit the SSM2044 IC is used, a 4 pole voltage controlled filter designed for electronic music applications. On-chip voltage control of resonance allows direct and easy interfacing with programmers and controllers. The IC features extended control range, low noise, and high control rejection. The filter can also be used as a low distortion sinewave oscillator...
The PWM controller uses complementary half-H peripheral drivers SN75603 and SN75604, with totem-pole outputs rated at 40 V and 2.0 A. These drivers effectively place the motor in a full-bridge configuration, which has the ability to provide bidirectional control. Timer U1 operates in the astable mode at a frequency of 80Hz. The 100-0 discharge resistor results in an 8-p.s trigger pulse which is coupled to the trigger input of timer U2. Timer U2 serves as the PWM.....
The single transistor connected between the capacitor and the common side of the ac line allows a logic-level signal to control this triac power circuit...
The preamplifier was designed to signal sources such as low-impedance moving coil cartridges (MC) on turntables high fidelity (and yet still there). The impedance of the amplifier is 100 W. To keep the noise levels low, three double-type transistors MAT03 SSM2220 or linked together to form a differential amplifier. Connecting this amp in front of an operand (OR27) is reduced to very low levels in noise input of the latter. The connections of the bases of the amplifier's.....
The controller circuit can reduce a fan"s noise, power consumption, and wear, particularly in the presence of a low, fluctuating ambient temperature. Mount a temperature sensor in the fan"s airstream, and the circuit will adjust the fan speed as necessary to maintain a relatively constant sensor temperature. Input components Rl and Cl integrate the input square wave, producing a quasitriangular wave at the noninverting input of op amp IC1A. At this inverting input is a.....
A 555 timer IC, operating in the one-shot mode, is triggered by light striking photoresistors. These normally have a resistance of several megohms but, in the presence of light, that resistance drops to several hundred ohms, permitting current from the six-volt source to flow in the circuit. The R-C combination shown gives an on-time of about two minutes. Photoresistors PC3 and PC4 are mounted at heatlight-height. When headlights illuminate the photoresistor, the timer.....
Temperature control is achieved using the REF-02 +5 V Reference/Thermometer and a CMP-02 Precision Low Input Current Comparator. The CMP-02 turns on a heating element driver (Ql) whenever the present temperature drops below a setpoint temperature determined by the ratio of Rl to R2..
The circuit will operate reliably from below 1 MHz to above 400 MHz. With Vcc = 5 V the output of the second inverter essentially attains a full swing from 0 V to 5 V. Such large logic output levels and broad frequency range capabilities make this oscillator quite suitable for driving MOS components such as CPU, controller chip, peripheral devices, as well as other TTL products...
The modified power-factor controller, developed at the Marshall Space Flight Center, employs a phase detector for each of the three phase windings of a delta-connected induction motor. The phase-difference sum is the basis for control. ..
The relay which applies power to the wiper motor is actuated at periodic intervals by the timer circuit, closing the wiper motor contacts. Potentiometer R1 serves as the pulse rate control and potentiometer R5 as the pulse width control. ..
Many applications require analog signals to be sensed and digital signals to be controlled. A way to detect these p..
The schematic shows a 50W power supply with a 5-V 10-A output. It is a flyback converter operating in the continuous mode. The circuit features a primary side and secondary side controller will full-protection from fault conditions such as overcurrent. ..
The ATMEL, with family AVR, was consolidated in the field of microcontrollers. The microcontrollers are, providing fast core and a variety of peripherals. These features continue to occupy the attention of engineers and earn their preference. The developer will see, it accepts all models of the family of AVR. It is an excellent tool that stands out for its high performance and simplicity in handling. To develop, based on the record of AVR, the AVRDONGLE.PDF. If someone.....
Most of you will certainly already installed on your computer one of the many software tools move freely from hand to hand and is suitable for programming the PIC 16C84. One of the most popular of this kind is the RIR02 of Silicon Studios. The circuit described below, is perhaps the simplest PIC programmer that can work seamlessly with the program RIR02. This guide allows RIR02 communication with the programmer, through the parallel port (Centronics). ..
The governor following is intended to regulate the light intensity incandescent 220 V. The components in a relatively few, which means it can easily be mounted onto a small plate. After the build, we recommend you place it inside the box which is flush mounted switch ON / OFF the lamp. Setting the switch to ON, the lamp will light after about 400 msec, a delay is probably negligible. But when the state enters the ON OFF, then mesolathei a period of 20 sec, the brightness.....
A phototransistor senses daylight. At dusk, it ceases to conduct and Rl biases Q2, activates Kl, and ..
Universal motors and shade d-pole induction motors can be easily controlled with a full-wave Triac speed controller. Q1 combines both the triac and diac trigger diodes in the same case. The motor used for the load must be limited to 6 amperes maximum. Triac Ql must be provided with a heat sink..
The circuit consists of an ICM7208 seven-decade counter (Ul), an ICM7207A oscillator controller (U2), and a CA3130 biFET op amp (U3). Integrated circuit Ul counts input signals, decodes them to 7-segment format, and outputs signals that are used to drive a 7-digit display. Integrated circuit U2 provides the timing for Ul, wliile U3 conditions the input signal to provide a suitable waveform for input to Ul. The 5.24288-MHz crystal frequency is divided by U2 to produce a.....
Just one chip, the PWR-DRV1 from Power Integrations, builds a "bang-bang" controller that switches 275 mA and runs of..
Relay K1 has a low-impedance coil and K2 has a high-impedance coil. When a sensor opens, current is routed throu..
Operational Amplifiers
Computer Systems
Oscilloscopes
Transmitters & Receivers
Sensors & Detectors
ANSI Standards
Low Frequency Amplifiers
Power Amplifiers
Number Systems
Regulated Power Supplies
Analogue Filters
Digital Gates
