Automotive Circuits
- Page 3
-
If you live in the frozen north, knowing your engine-block heater is working is a comfort. This device will let you know if yours is okay. Plug in PL1 to your power outlet. NE1 should light. Then, plug in the block heater. Depressing SI should cause the....
-
-
A normally open pushbutton switch (SI) delivers a positive input pulse to pin 4 of Ul, triggering the 1C into action. The output of Ul at pin 6 supplies base-drive current to a Darlington pair comprised of Q1 and Q2, activating . 10- capacitor and any....
-
This alternator regulator uses a 3-transistor dc amplifier, and is designed for a pulled up field system, where one side of the alternate field returns to the +12-Vsupply, and the other end is pulled toward ground...
-
This regulator is for the purpose of controlling a dc generator. The field configuration is that one side of the field is grounded. D4 prevents the battery from discharging through the generator and takes the place of the mechanical cut-out relay...
-
A relay and two diodes are all tliat is needed the relay performs the job of a buzzer so no annunciator is required. When the lights are left on, but the ignition is off, the normally closcd relay contacts are in series with the relay coil. That means the....
-
The base of Ql is connected to the car`s ignition circuit; the easiest point to make that connection is at the ignition switch fuse in the car`s fuse panel. Also, one side of the piezoelectric buzzer is connected to the instrument-panel light fuse; when the....
-
-
This battery saver circuit can automatically turn off a small piece of test equipment after a desired period of time, allowing you to leave your shop worry free.This circuit uses a CD4011IC to act as a simple timer. One section acts as an RC discharge timer....
-
This circuit uses the 555 timer in the asta-ble or oscillatory mode. The length of time the timer is off is a function of the values of CI, R2, and R3. The potentiometer which controls the amount of "hesitation"..
-
A diode (IN4148) is used as a temperature sensor. IC2 is an A/D converter with BCD output. A refere..
-
The circuit, is based on a commercial temperature sensor (TS6178) and an MC3334P ignition chip, When the radiator temperature increases, the sensor pulls the base of Q2 low via Ql, which is wired as a diode. Q2`s collector thus goes high and triggers IC1,..
-
Because the power controller is powered from the vehicle`s accessory switch, the load can receive power only when the ignition key is on. Using half of a dual flip-flop (CD4013), a load of up to 10 A is controlled by a momentary pushbutton. This circuit was....
-
-
When the ignition switch is on, relay K1 is energized continuously, and the headlights can be turned on. Turning off the ignition turns on timer IC1,which keeps IC1 energized for a time determined by Rl and CI. With the values shown approximately a 1 minute....
-
This circuit determines the cold cranking amps of a battery by first discharging the surface charge, then checking the internal resistance. This gives a more realistic measurement than simply measuring the instantaneous drop in voltage with a load. A....
-
The monitor is a simple voltage comparator in which a car battery serves as the battery for operation. The input voltage to the comparator is set by adjustment potentiometer PI, which must be adjusted so that the green LED L2 is on when the alternator is....
-
The SN75604, with input control logic but requiring only one supply rail, can be used in the "lights on" sensor and alarm driver. The device Vqq and enable inputs are connected to a voltage lead from the light switch. The direction control input is connected....
-
The circuit is used to indicate two different water temperature trip points by turning on LEDs when the temperatures are reached. The circuit is constructed around the LM2904 dual operational amplifier powered from the 12 V auto system. The thermistor is in....
-
The circuit warns car drivers when the air temperature close to the ground approaches 0°C, thereby indicating possible formation of ice on the road surface. Op amp A1 is wired as a voltage level sensor. Op amp A2 is wired as an astable multivibrator which,....
-
The Digi-Tach contains a master-clock circuits (U6)v latch and reset pulse generators (U2-b-U2-d), input signal bonditioner (Ul, U2-a), pulse counter (U3), display and display drivers (DIS1, DIS2, U4, and U5), and a voltage regulator (U7)...
-
The relay which applies power to the wiper motor is actuated at periodic intervals by the timer circuit, closing the wiper motor contacts. Potentiometer R1 serves as the pulse rate control and potentiometer R5 as the pulse width control. ..
-
U1 is configured to operate in the standard astable mode, providing a form of relaxation oscillator. When power is applied, C2 initially charges through Rl, R2 and R3 to two-thirds of the supply voltage. At that point, U1 senses that its threshold voltage at....
-
The car alarm here is a simple circuit with basic characteristics that cover all entrances at the car that has switches (doors etc).With one switch (arm-switch) the circuit waits for the sensor-switches to open and to activate it. So the horn with 1 sec....
-
A flip of 51 puts the system in action. Power for the circuit is captured from the ignition switch, and circuit receives no power until the ignition switch is closed. When the camera is turned on, the capacitor C1 is charged and the emitter follower....
-
model airplanes, boats, cars and use of ignition of glow plugs for their miniature (O. Bcc to 15cc) internal combustion engines. These engines happen with the heavy batteries on board, HT coil, and "condenser" spark required for ignition classic, while....
-
The circuit provides a windshield wiper delay, dynamic braking and windshield wipers when they reach the rest position. This prevents the blades passing, which could lead them to stop at a point where they interfere with the vision of drivers. With the....
-
Circuit works: lC is a 555 IC. Incoming calls, 220 V electricity through R1 Buck, VD1 rectifier, DW regulator, C2 filtered to give 12 V DC voltage of about...
-
1 Bute CD12V Lee output end of the eight-connected MOSFET power transistor BU * {1RF744) im JUV bone made this power MOSFET is turned on and should go off repeatedly called to ask L packet..
-
This paragraph Easy Car Alarm circuit with the use of fewer components, easy to produce and so on. (1) circuit automobile anti-theft alarm circuit by the time base circuit NE555, power switch VT, the switch S2, the..
-
Circuit works: lC1 is lock ASIC 5C058. Its 1-6 feet were even outside the key switch to the positive power supply, which is six valid key input, open lock A-F must comply with this order. 7 feet for the negative power. 8 feet false key input terminal, even....
-
A Mitsubishi Pajero car audio, fault phenomenon is silent, and the rest feature to work, the search for the amplifier IC TA8205AH damage. TA8205AH Toshiba company produces 22W ..
-
An automobile permanent magnet alternator failure, the phenomenon of cars at night driving, headlights suddenly increase in brightness, then goes out. Analyzing the generator v..
-
Anatomy of the two ignition experiments, measuring the three normal ignition, found a common problem, and both ends of the ignition coil has a diode. Why manufacturers do this ..
-
Anti-theft car audio system circuit is shown, which is taken from the car battery 12V DC power supply. When after closing the switch S1. Optocoupler IC1 light emitting diode is..