Remote control using telephone

Posted on Feb 5, 2014

Here is a teleremote circuit which enables switching on` and off` of appliances through telephone lines. It can be used to switch appliances from any distance, overcoming the limited range of infrared and radio remote controls. The circuit described here can be used to switch up to nine appliances (corresponding to the digits 1 through 9 of the te

Click here to download the full size of the above Circuit.

lephone key-pad). The DTMF signals on telephone instrument are used as control signals. The digit `0 ² in DTMF mode is used to toggle between the appliance mode and normal telephone operation mode. Thus the telephone can be used to switch on or switch off the appliances also while being used for normal conversation. The circuit uses IC KT3170 (DTMF-to-BCD converter), 74154 (4-to-16-line demult-iplexer), and five CD4013 (D flip-flop) ICs. The working of the circuit is as follows. Once a call is established (after hearing ring-back tone), dial `0 ² in DTMF mode. IC1 decodes this as `1010 ², which is further demultiplexed by IC2 as output O10 (at pin 11) of IC2 (74154). The active low output of IC2, after inversion by an inverter gate of IC3 (CD4049), becomes logic 1. This is used to toggle flip-flop-1 (F/F-1) and relay RL1 is energised. Relay RL1 has two changeover contacts, RL1(a) and RL1(b). The energised RL1(a) contacts provide a 220-ohm loop across the telephone line while RL1(b) contacts inject a 10kHz tone on the line, which indicates to the caller that appliance mode has been selected. The 220-ohm loop on telephone line disconnects the ringer from the telephone line in the exchange. The line is now connected for appliance mode of operation. If digit `0 ² is not dialed (in DTMF) after establishing the call, the ring continues and the telephone can be used for normal conversation. After selection of the appliance mode of...

Visit page

Leave Comment

characters left:

Related Circuits

Silent Radio LED sign to Arduino

Working on the brightness problem, I know that the 4017 design did not work well because there was no way to turn off the sign while updating the shift registers. As a result I went back to having...

Laser Microphone

This was a final project for an optics class EE 134 at Stanford. It was an open-ended project to make a fully functioning laser microphone the class was geared to demonstrate optics and photonics...

relay circuits

Remove the 6 mm screw holding on the lower rear fairing cover. This is the black plastic piece the spark plug protectors are attached to. Do not remove the lower rear fairing covers, only the...

Single Capacitor Powers Audio Mixer

Micropower and low-voltage op amps allow you to build high-performance analog-signal processors that require no batteries or wall transformers. Instead, you can use a capacitor as a power source....

Berkeley Bolometer Group - Research

Bolometer systems would be simplified considerably if all components could be made photolithographically on a single substrate. We are developing a design for a single-substrate array with several...

Design of VLSI Systems

Clock signals are the heartbeats of digital systems. Hence, the stability of clock signals is highly important. Ideally, clock signals should have minimum rise and fall times, specified duty...

ARCHITECTURES FOR VIDEO PROCESSING

The first question we would like to answer is: what do we mean nowadays for video processing In the past, more or less till the end of the 80`s there where two distinct worlds: an analog TV world...

DC Lessons In Electric Circuits

A meter is any device built to accurately detect and display an electrical quantity in a form readable by a human being. Usually this "readable form" is visual: motion of a pointer on a scale, a...

New Circuits

Zero consumption Anti-theft High power Code Switch for E-Bike Batteries

This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of....
Ultrasonic distance finder circuit

The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is....
Simple Metal detector circuit with CD4030

Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to....
Fully automatic watering circuit for flower pots

Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This....
Simple deep searching metal detector circuit

The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the....
Sub-Harmonic Bass Converter for Electric Guitars

The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,....
Echo Depth Sounding Sonar for Boats

In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the....
100W HiFi Audio Amplifier Circuit

This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power....
Plant-Pot Water Level Indicator Circuit

A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....

Create NOW your QR MENU for your Restaurant / Hotel / Bar / Caffe,

Comprehensive ordering/paying features. fully personalized to suit your Business.

Update Anytime! Easy and Simple!

Popular Circuits

sound detector tone decoder

This circuit is designed to trigger on a 1 khz tone. to change this frequency - refer to the...

Toggle Switch with relay

Pushing the button once will energize the relay. Pushing the same button a second time will...

Wireless LCD Display (AT90S2313)

Its an adaptation of the 2X 16 LCD project, by adding a fettite loop antenna, two resistors, and...

Low-Ohms Adapter

The circuit consists of a 5-V regulator, constant-current source Dl, D2, and Ql, and op amp gain...

1.3W RF Amplifier Circuit

The following diagram is the circuit diagram of 20W power amplifier which build based tube...

Simple 6V charger battery circuit Schematic Diagram

This is very simple charger 9V - 30V battery charger with main operation by IC LM317L and 2N222...

automatic low power emergancy light

A white-LED-based emergency light that offers the following advantages. 1-It is highly bright due...

robot2

This page contains circuit diagrams and code for a walking robot I made using Mark Tilden`s...

Zero rectifier regulator schematic

The pre-regulator circuit connected to the capacitor, resistor element. Regulator in its...

Blackout emergency lights 4

Charging circuit by the transformer Tl, diode VDI-VD4 and other components, 220V AC by Tl buck,...