Repository-circuits
- Page 592
-
This LASER is constructed on a polystirene sheet. An alluminium layer foil is placed and acts as a ground plate ( - ), this is important for preionization (i will discuss it later). After that the dielectic is placed on it leaving 1 cm from each border of....
-
-
Knowing the three operational modes the 555 timer offers, it`s not hard to imagine its many applications in IC circuit designs: Oscillator: The 555 timer can be used as a simple clock pulse generator (up to 1 or 2 MHz) A monostable timer is a one-stable....
-
Using a battery power source the TENS device produces a high voltage but low current signal at a specified frequency and duration. This electrical current is applied externally to the skin of the body using sticky foam electrode pads. The more expensive....
-
The reson this was made this was, was to make first installation fast an a local freiend 10km away, so i cuold start real life testing, so bugs and problems can be solved before this is gived free to all other users. Software is not complete yet, all is....
-
Don`t forget to seal your wire splices with heat shrink. It adds tensile strength to wires, is flameretardant and protects them from fraying. Heat shrink tubing forms a protective, insulated, water-resistant covering over wiring splices, crimp terminals and....
-
LM5576MHX absolute maximum ratings: (1)VIN to GND: 76V; (2)BST to GND: 90V; (3)PRE to GND: 76V; (4)SW to GND (Steady State): -1. 5V; (5)BST to VCC: 76V; (6)SD, VCC to GND: 14V; (7)BST to SW: 14V; (8)OUT to GND: Limited to Vin; (9)SYNC, SS, FB, RAMP to GND:....
-
-
-
NE5532DR absolute maximum ratings: (1)Supply voltage: VCC+ 22 V; VCC-: -22 V; (2)Input voltage, either input VCC ±; (3)Input current: ±10 mA; (4)Duration of output short circuit: Unlimited; (5)Package thermal impedance, JA: D package 97ƒ/W; P package 85ƒ/W;....
-
-
-
I needed to test some crystals for a project I was working on. I found lots of testers on the internet, but they all where lacking in one thing or another. I decided to take one of them and add the features that I wanted to it. This is the result. I also....
-
-
There are two independent modeling light circuits for the P2000D - one for each of the two channels. The modeling light circuit is completely independent from the high voltage strobe circuitry - to the point of having its own On/Off switch. This means, of....
-
This page provided to the domain owner free by Sedo`s Domain Parking. Disclaimer: Domain owner and Sedo maintain no relationship with third party advertisers. Reference to any specific service or trade mark is not controlled by Sedo or domain owner and does....
-
-
-
-
This is a reproduction of the filter circuit and mic windshield design referred to in the article "Wildlife Recording In Stereo" by David J Tombs which appeared in 1974...
-
-
The second method is to record (realtime) the actual bark in an analog CCD delay line (~100 msec FIFO) and upon recognition that the sound is a bark, the device plays back-through a loudspeaker-that last recorded 100 msec of bark. It really confuses them;....
-
A FET impedance converter for use with the Fishman pickup on my Kay orchestra bass. As shown in the schematic below, the circuit is divided into two sections, so that the input section can be mounted inside the head shell of a 1/4" plug. This puts the active....
-
The major functional blocks necessary to design a general purpose audio oscillator, and give all the details of my current prototype. Implementation is in the mode of an analog computer, since the desired outputs are sine and cosine values as a function of....
-
How to use a desktop computer to solve the complex arithmetic needed to design state-variable filters for audio use. Construction of a tunable notch filter for measuring harmonic distortion is featured. Audio Amateur Corp. did a beautiful job (as always)of....
-
A tone generator that runs on as little as 1. 5 Vdc, using the Sallen-Key configuration. And finally, I`ll apply the tone generator to implement a phantom powered signal source for testing balanced microphone inputs. Textbooks and web pages usually show the....
-
Requires that DC power be brought into the instrument, either through special cabling or an internal battery. Should not be done to collectible instruments if they didn`t come with onboard electronics. Conveniently implemented as a field effect transistor....
-
To hook up the three Pot connections you will firstly need to establish the tags and the positions that I refer to. If you take the pot and look at the back of it, then make sure that the tags are at the top of the pot, then; The only thing that will happen....
-
I`ve managed to complete the first phase of my motion-controlled photography rig: setting up a pair of bipolar stepper motor controllers. This is the most important non-mechanical part of the project, as without control of motors there can be no....
-
You will need an oscilloscope capable of displaying in X/Y mode, and a reference "LO" signal source. In-phase and Quadrature reference square wave signals are generated by a divide by 4, 2 bit ring counter using 2 D type flip - flops. So that I could use an....
-
The Hex switches are connected to J2 as follows: pin 1=common of both switches (+5V) 2=LSB up to 5=MSB of first switch. Then 6=LSB of second switch up to 9 which is MSB. I modified the oscillator slightly to get my cheap Farnell crystal to start reliably....
-
When a key is pressed the remote control sends a preamble followed by 32 bits of information encoded using these pulse timings. Examples of these pulses can be seen below as logic analyser screen dumps (the glitches are bugs in the Logic analyser software).....
-
A Cmos 4060 Burglar Alarm Circuit This is a single zone alarm - with automatic exit, entry and siren cut-off timers. It will accommodate all the usual types of normally-closed input devices - such as magnetic-reed contacts - foi....
-
A Cmos Based Motorcycle Alarm Circuit This circuit features an intermittent siren output and automatic reset. It can be operated manually using a key-switch or a hidden switch; but it can also be wired to set itself automaticall....
-
A Dozen Small Cmos Alarm Circuits Circuit Description This is a selection of small self-contained alarm circuits. The main features of each alarm are described on the circuit diagram itself. They all have a very low standby current. So they This is a....