Decoder Circuits
- Page 3
-
-
-
-
-
-
This project has an impossible requirement or uses parts that are no longer available. It is here for reference or inspiration only. Consider it unsupported . This project displays telephone numbers decoded from tones. Specifically, telephone touchtones.....
-
Here is the circuit diagram of an FM remote encoder/decoder using the ICs RF600E and RF600D. These devices are designed to provide a high level of security and operates from anything between 2 to 6. 6V DC. Various electronic circuits like remote control....
-
-
Simple FM stereo decoder circuit using MC1310P IC. 12V operation, 40dB channel seperation. Suitable for stereo FM receivers....
-
This circuit shows about NE5532 IC For FM Stereo Radio Decoder Circuit Diagram. Features: simple circuit, using NE5532 IC. Component: IC, ....
-
Encoder and Decoder are circuits which converts the analog signal to digital and digital signal into analog signal. Its input will be in digital form while the output will be a continuous sine wave or analog wave....
-
The Supertex HV440 is used for implementing a pulse width modulated high voltage ring generator for telecommunication applications. The HV440 CAN operate in both closed-loop or open-loop. A closed-loop design is more complex but provides better load....
-
The MT8870 is a complete DTMF receiver integrating both the bandsplit Filter and digital decoder functions. The Filter section uses switched capacitor techniques for high and low group filters; the decoder uses digital counting techniques to detect and....
-
-
500 Series immersion temperature probe, NTC, 100, 000 Ohm, ±1, 5 °C [2. 7 °F] tolerance, 10 °C to 260 °C [50 °F to 500 °F] accuracy, stainless steel, bullet housing, flying leads (two), 26 gauge Teflon insulation, 4, 267 mm [168 in] ..
-
-
The STI5211 is a standard definition, full back-end processor for satellite set-top boxes, compliant with ATSC, SMPTE VC-1, DVB-S2, DIRECTV, DCII and ARIB BS4 specifications. It provides very high performance for low-cost SD systems. With its enhanced....
-
The STI7167 uses state-of-the-art process technology to provide a fully featured HD AVC DVB-C and DVB-T Demodulator and decoder IC. It is a highly integrated system-on-chip suitable for STB markets across cable, terrestrial, and terrestrial/IP hybrid....
-
The STK672-050 is a unipolar constant-current chopper- type externally-excited 4-phase stepping Motor Driver hybrid IC which uses MOSFET power devices. It has a microstep operation-supported 4-phase distributed con- troller built-in to realize a high torque,....
-
The TA2003PG TA2003FG are AM / FM Radio IC (FM F / E+AM / FM IF) which are designed for AM / FM Radios Combining with the TA7368P (Mono PW IC), a suitable AM / FM Radio system is able to be constituted. By Toshiba Semiconductor ..
-
The TDA3592A transcoder circuit converts SECAM input signals into true PAL signals, and CAN be used in combination with all types of PAL decoder By NXP Semiconductors ..
-
The TDA8340 Q and TDA8341 Q are integrated IF Amplifier and Demodulator circuits for colour or black/white Television receivers, the TDA8340 Q is for application with n-p-n Tuners and the TDA8341 Q for p-n-p Tuners The TDA8340 Q and TDA8341 Q are....
-
It`s very simple circuit using DTMF decoder MT8870 (or CM8870). As shown in the circuit, u`ll receive an interrupt ( if NAND output is connected to INT of the microcontroller) whenever u receive a call or make a call and then u can use yr program to read the....
-
This is a guest post by Olger Groen . If you would like to write for ExtremeCircuits, then drop us an email via contact form or simply comment. A long tim....
-
This is a background music (SCA) decoder circuit from the input demodulated (multiplex) FM signal. We use NE565 (Phase Locked Loop IC) to be base of this....
-
The problem is when i connect the 8051 to the encoder the data send is not received at the receiver but as soon as the 8051 connections are removed the transmisison works perfectly. thus manually the RF communication works perfectly i. e the 8 bit data which....
-
The pilot detector output is designed as an open collector output, therefore an external pull up resistor is needed. To force the decoder to "MONO" Pin 19 has to be clamped to a voltage below 0. 8V. ..
-
This circuit detects the dial tone from a telephone line and decodes the keypad pressed on the remote telephone. The dial tone we heard when we pick up the phone set is call Dual Tone Multi-Frequency, DTMF in short. The name was given because the tone that....
-
A simple stereo tv decoder circuit build with MC1310P. Transistor Q1 is an audio amplifier and U1 is used as a 31. 5KHz subcarrier which is similar to 38KHz FM MPX. Pilot frequency is 15. 734KHz. No, it cannot be used with the to decode the stereo signal.....
-
-
The Glolab ED4GP microprocessor based Encoder / Decoder is designed for use with wireless modules, infrared remote controls and other devices that operate with serial input and output data. It can be used as either an encoder or a decoder by simply....
-
I have been getting a lot of emails about this project. Most of them are because of the bad source code listing at the end of the author`s notes. I have seen this problem all over the web and I too have ran into the same problem when compiling the code. I am....
-
-
-
It can be possible and it can be implemented using P-MOS and N-MOS together in a circuit i. e. what is called C-MOS. There we can implement Three Terminal NAND GATE. It is a universal gate which is used commonly so can proceed further...