Infrared Circuits
- Page 10
-
This infrared alarm barrier can be used to detect persons passing through doorways, corridors and small gates. The transmitter emits a beam of infrared light which is invisible to the human eye. The buzzer at the output of the receiver is activated when the....
-
-
TX05C-R infrared surveillance alarm circuit is shown. It can be used for surveillance of walls, windows, doors and various restricted areas. If someone breaks into or over the alarm position, it will sound to play a security role. The circuit consists of....
-
See as the circuit, it consists of the infrared sensor control circuit, relay control circuit, music generating circuit and so on, which can be used in infrared alarm, timing control and other spots....
-
No matter what kind it is, passive human body infrared sensor circuits are almost the same with the above, maybe some has less stages. This circuit in the figure is got from the NICERA producer, which is classical. The stage of front-end is the low frequency....
-
-
The circuit work theory This infrared automatic hand washing device circuit is composed of power supply, infrared transmitting circuit, infrared receiving circuit and control circuit, the circuit is shown in the figure 9-121. The power supply circuit is made....
-
-
-
This circuit uses the HgCdTe demodulation device which can be cooled to 77K in liquid nitrogen. It uses a constant current bias for the demodulation device which is connected to the input port. The voltage`s amplification factor is 200 and the bandwidth is....
-
As shown in the figure, it isa sensing automatically lightmade by newHN911L pyroelectric infrared detection module. The HN911L integrates high - sensitivity infrared sensors, PIR, amplifiers, signal processing circuit andoutput circuit. Itisable to remote....
-
Because of the transmitter circuit of the inductive headphone must installed on the room wall or on the ceiling, so the inductive headphone can not be used outdoor, this is the main weak point of the inductive headphone. But the infrared rays wireless....
-
-
-
Figure (a) is the infrared emission circuit that composed of 12 the keyboard and S2559. Figure (b)shows DTMF decoder circuit and channel control circuit composedof the MT8870. Figure (c) is the voltage amplifier circuit composed of two-op ampLM358....
-
The DTMF codec is the abbreviation of the dual-tone multi-frequency codec. The multiple-channel infrared remote control switch circuit which is composed of the DTMF is as shown in the figure. It is composed of the infrared remote control signal emitter, the....
-
-
The DTMF infrared remote control circuit. The DTMF encoded signal can be decoded by the special decoder and the PLL audio decoder LM567. But the DTMF encoded signal which is decoded by only one decoder, has only one frequency, one group of control signal is....
-
LS-2 remote control switch infrared sensor module is basically the same with the LS-18, in addition, it isused as a reflector. LS-2 Pin diagram form LS-2 internal block diagram Electrical parameters LS-2 remote control switch module operating voltage is 4 ~....
-
-
The receiving circuit: the infrared signal is inputed to MC3373 from 7 foot by phototube, the amplified signal outputs from 1 foot, it is transported into the 12 foot of decoder 8802. When the transmitter F is pressed, the voltage of 8802`s 11 foot up to 2.....
-
The HT6337 is designed as one kind of infrared remote control receiving decoder circuit that can be used in the electric fan application. It uses the 28-pin dual-row DIP package, the matching model is HT12C. The HT6337 is one of the series products. The....
-
The diagram is human infrared remote sensing lamp circuit. It uses trace infrared heat sent out by human to remote control the open or close of lap. This human infrared remote sensing lamp trigger sensitivity is very high ( can work in 10m distance),....
-
-
-
The SC41343 is designed as one kind of infrared, ultrasonic or RF remote control launch coding circuit. The internal circuit is composed of the sequence generator, control logic circuit?4-bit shift register?data extraction circuit and the latch circuit.....
-
The SL517 is designed as the audio, RF or infrared decoder circuit that can be used in the electronic toy application. The internal circuit is composed of the analog amplifier, the frequency divider, the bistable circuit and the driver. Features It uses the....
-
Pyroelectric infrared sensor head is same with the figure. When it detects the human body infrared signal in guarding zone, the sensor head will output a positive jump pulse signal, this signal is added to input terminal P point. IC1 adopts 555 time base....
-
A few time ago I decided to create a media center box to replace my DVD player, sattelite receiver, VCR and my kid`s Play Station 2, toone device. So, I made a core 2 duo processor system that actually replaced with succeed, all my electronic devices. The....
-
-
This is infrared (IR) proximity detector circuit. A matched infrared emitter and detector pair is used in this circuit. The voltage controlled oscillator....
-
Infrared transmitter and receiver circuit shown in the schematic diagram below can be used as remote control. The transmitter is basically an oscillator....
-
This relay circuit is controlled by almost any type of infrared remote controller. This circuit works on assumption that almost all remote controller use high....
-
The transmitter offers a optical link (infrared) for headphones. Three infrared leds (ir) are polirised by T1 current, P1 is used to adjust the current level. Current consumption of this headphones infrared transmitter is about 60mA at 9V....
-
Here the long range/distance Infrared transmitter circuit, give you extra power for your Infrared transmitter. The majority of the IR remotes do the job reliably within a range of 5 metres. The circuit complexity increases in case you desig....