Electronic Switch ON-OFF

Posted on Aug 12, 2012

Here we have three choices, with which we can make electronic switches that use our touch or pressing (push button). We thus exploit the very big resistance of entry, that present the gates CMOS. In the fig.1 we have two gates NAND or NOR (IC1), connected as R-S flip-flop. Just as we press the switch S1, the exit 3 it becomes [H], even it is maintained in this situation. To change the situation, it should we press switch S2. Now exit 3, takes price (L), reversely exit 4 becomes (H). In order to we maintain the situation that we want, we can connect at parallel with the corresponding switch, a capacitor C=100nF.

Click here to download the full size of the above Circuit.

This entry will always drive the corresponding exit to logic (L), immediately afterwards the benefit of supply to the circuit. In the fig. 2, we have a circuit of inverter CMOS, in the entry of which is applied logic situation (H), from the resistance R, which the other end of, is in the supply. Exit 2 has situation (L). When we press switch S2, in the entry of 3 IC2, we have situation (L), this it goes to the ground, the exit now becomes (H). This situations are maintained as long as we keep pressed switch S2 and they change immediately hardly the touch. If we want opposite logic operation then it will be supposed we connect the resistance R, in the ground and switch S2, in the supply. The same logic we will have if we replace gate IC2, with a gate NAND or NOR, as it appears in the fig. 3, the result is the himself. Because the situation in the case of fig.1 and 3, does not remain constant and change when we pull our finger , in order to him we retain, it should we connect a J-K or D flip-flop as T, after the IC2 and IC3. Thus the flip-flop, will change situation, each time where we will touch the switch or will touch the contacts and him it will retain. All the switches can be replaced with contacts, it is enough we replace also resistances R with the price of 10M?. The Resistances R when we use pressing switches can are, from 100K? until 1M?. Because when we use contacts instead of switches, the noise can turn on the...

Visit page

Leave Comment

characters left:

New Circuits

Zero consumption Anti-theft High power Code Switch for E-Bike Batteries

This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of....
Ultrasonic distance finder circuit

The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is....
Simple Metal detector circuit with CD4030

Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to....
Fully automatic watering circuit for flower pots

Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This....
Simple deep searching metal detector circuit

The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the....
Sub-Harmonic Bass Converter for Electric Guitars

The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,....
Echo Depth Sounding Sonar for Boats

In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the....
100W HiFi Audio Amplifier Circuit

This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power....
Plant-Pot Water Level Indicator Circuit

A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....

Create NOW your QR MENU for your Restaurant / Hotel / Bar / Caffe,

Comprehensive ordering/paying features. fully personalized to suit your Business.

Update Anytime! Easy and Simple!

Popular Circuits

PWM Motor Speed Controller

A pulse width modulator (PWM) is a device that may be used as an efficient light dimmer or DC...

A class and push-pull

Pure A class is the most simple topology for designing an amplifier! The tube or the power...

Guitar Tremolo Unit

The unit is simple to build, and does not need really low noise opamps, since they only act as a...

3 LED - 1 Cell battery tester

The device serves to quickly establish the status of an indicative power cells. I built it for...

Logic Probe

By connecting this circuit to a logic device that"s under power, you can get an indication as to...

3.3V and 5V DC DC converter circuit design using LT3692 DC converter dual tracking regulator

Using the LT3692 dual current mode PWM step-down DC DC converter circuit with two internal 3. 5A...

Build an Experimenters Power Supply

Note the incoming ac routed to the primary terminals on a 12. 6-volt transformer. The hot side...

Glow Plug Driver for R/C Flightbox

All errors in circuit diagrams, documents and layout are corrected. The circuit as shown below is...