Phone Circuits
- Page 10-
Simple telephone time lock circuit is shown in the above picture. In the circuit diagram, BG1 and BG2 are electronic switches controlled by IC NE555. When the telephone is on-hook, the DC resistance value of the telephone is over 600K?, the current when the.... -
Using an AMI chip P/N S2561, this telephone ringer can be powered line. Audio output is about 50 mW when powered from a 10-V source.... -
Tro telephones can be used as an intercom by using this circuit. Older style rotary phones that are nonelectronic might work best in this application. Also, handsets only might be powered this way.... -
The diagram shows telephone control automatic lighting circuit. At night, when telephone rings or master takes up telephone transmitter dialing, the light can lighten; when telephone ringer stopped (no one listen) or on-hook, it can delay 10~40s, then the.... -
The simple circuit below regulates the voltage from a 6v solar panel to a fixed +5v. That voltage can be fed to any cell phone or USB connected portable device, to charge its battery. The circuit uses a Reg113-5 voltage regulator from Texas Instruments. The.... -
Internal telephone circuit is shown as below,improving slightly a toy telephone will become a variable practical internal telephone. This phone is compose of the phone component,decoding circuit,ringing circuit and other components. Using more than two the.... -
Telephone electronic coded lock circuit is shown as above,the electronic coded lock is suitable for double audio circuits.After the phone adds this coded lock, when you call out,you must use the buttons on the phone to press the four pre-programmed.... -
Telephone electronic ringer circuit is shown as above,Figure (a) is the electronic ring circuit with an NPN transistor V1 (choose 9014 or 3DG12) as the core, sound devices YD is also feedback devices composed of the feedback pole and the buzzer equipped with.... -
This is a phone bug circuit. This wireless telephone line spy circuit can be used to transmit the phone conversation to a nearby FM radio. This circuit must.... -
This is a circuit of phone message flasher, an alternative way to get alarmed when there is an incoming call. When the phone rings, high line voltage will be.... -
This is a switch selectable dual output "re-hashed" version of my previous (2007) design, and uses a field programmed EPROM for generating both versions of the ringing sequence. AC mains is stepped down to about 10 v AC and fed to the familiar bridge.... -
When a new computer modem enters the household, the demands on the home phone line skyrockets. The Internet surfer can use phone time on a par with the most talkative teenager. And the computer modem user can be quite sensitive about his privacy: simply.... -
This circuit generates the sound of the electronic ringer found in modern telephones, supplanting the 2-bell electromechanical ringers used previously. The ringing pattern follows the United States convention of 2 seconds on, and 4 seconds off. During the.... -
Voicemail capacility (although not implemented, there are four ADCs that can be used to sample and record the phone audio) A storage volume (SD card) would need to be connected. This project was inspired by these other homemade exchanges: Markus Wandel and.... -
How to interface a microcontroller to the phone line. The tones you hear as you enter numbers on your phone can remotely control devices. Learn how to use these DTMF tones in your microcontroller projects. This article was submitted by Mayank Magoo as part.... -
The type C system was first installed about 1925 and has been very extensively used. It incorporates the most desirable features of the systems just considered. Like the type A system, the carrier is suppressed, and hence the effect of line attenuation is.... -
Join the forum discussion on this post This is a simple home telephone ringtone generator circuit which is built with applying only several electronic components / parts. It generates simulated telephone ringtone and requires only DC supply.... -
This diagram is the schematic diagram of telephone switcher using relays. This device connects to the telephone line and can be used to remotely control up to 4 relay outputs using a DTMF (tone dialing) telephone. A number of user settings....
Neighbour Categories
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
The EDFET drives like a FET, but with the bias stability of bipolar. Amps of output current can...
This amplifier has Output power about 500 Watt with the compatible voltage supply is under 63...
Many integrated circuits have undocumented features or abilities. This is one of them. The TLC555...
Simple counting can be done by anyone but counting in interval up to large number is tedious and...
New cellular phones have incorporated high resolution cameras, which require high brightness...
Timer circuit has been used in many projects and there are basically 2 types that are used these...
The idea for this circuit came when the author had problems with the wireless speedometer on his...
Vegetable greenhouse temperature detection control circuit Greenhouses temperature detection...
Voltmeter by the measuring mechanism in a given circle and moving coil in series to configure...
As shown in FIG, XTR106 has two internal source voltage (2.5V and 5V) to provide incentives, and...
Figure (a) shows a block diagram of the internal structure of the M62213FP. M62213FP is a high...
This transmitter of 255W is depended on the coils we put at it to work in both the middle and the...