Creating Fast Line Transients
The response of an integrated circuit to fast transients on its input supply is a critical measurement. For micro-power devices that do not require an input bypass capacitor, a 50-ohm terminated function generator can be used to drive the power-supply input. However, as current requirements and capacitance increase, this method may yield unsatisfactory results. A viable solution for managing fast transients with large capacitive loads is to implement an open-loop buffer. An open-loop buffer, lacking feedback, remains insensitive to capacitive loads and can be engineered to meet various current requirements. Key specifications for this buffer include a high slew rate, substantial output drive capability, low offset voltage, minimal distortion, and thermal compensation. The accompanying circuit diagram meets these specifications and resembles a traditional BJT buffer with modifications. Since the transistors are not integrated on a single monolithic die, a bias adjustment mechanism is necessary, along with a method for maintaining constant bias under varying temperature conditions. The circuit comprises three primary sections: a high-impedance complementary input stage, a VBE multiplier for bias adjustment, and a complementary Darlington output stage. The input stage and VBE multiplier are powered by constant current sources, while the output stage receives bias from the VBE multiplier. Series resistors R7 and R8 connect the input stage to the VBE multiplier and output stage, allowing the VBE multiplier to manage output stage bias without conflicting with the input stage's bias levels. This consideration is crucial as the output stage generates heat due to load demands. Without these series resistors, the input stage could excessively bias the output stage at elevated temperatures. The VBE multiplier is mounted on the output heatsink, ensuring it thermally tracks the output stage and prevents thermal runaway. This circuit is designed for bipolar power supplies, operating approximately 5V above the maximum output and 5V below the minimum output, with +15V and -5V providing optimal performance. Multiple grounds are included on the board, and input supplies should utilize a short pair of heavy-gauge wires to the PCB, avoiding shared grounds with other circuitry. The output should connect to the DUT input with very short, heavy-gauge wires capable of carrying transient currents exceeding 10A. The buffer features a high input impedance to accommodate flexible drive requirements. It is important to avoid connecting the buffer's output to the DUT input without a driving signal present at the buffer's input. For output voltages under ±5V, a 50-ohm terminator should be placed directly at the buffer input. For output voltages up to 10V, the pulse generator can operate unterminated. Voltages exceeding this range will necessitate an external amplifier. The maximum supply voltage for the buffer is limited to |V+ - V-| < 40V.
An open-loop buffer circuit is essential for applications requiring rapid transient response, especially in environments with significant capacitive loads. The design employs a high-impedance input stage, which minimizes loading on the signal source while ensuring accurate signal reproduction. The VBE multiplier serves as an effective biasing mechanism, adjusting the bias current dynamically based on temperature variations. This feature is critical in maintaining consistent performance across a range of operating conditions.
The complementary Darlington output stage is designed to deliver high current gain, making it suitable for driving loads that require substantial current without sacrificing stability or introducing distortion. The inclusion of series resistors R7 and R8 is a strategic design choice that enhances the circuit's robustness by ensuring that the biasing of the output stage is not adversely affected by changes in the input stage's operating conditions. This design consideration is particularly important in high-power applications where thermal effects can significantly influence circuit performance.
The circuit's layout should prioritize short, direct connections for both power and signal paths to minimize inductance and resistance, which can degrade performance during transient events. The use of heavy-gauge wiring for connections that carry high transient currents is essential to prevent voltage drops and ensure reliable operation. Additionally, careful grounding practices should be observed to prevent ground loops and noise interference, which could compromise the integrity of the measurements taken with the buffer.
Overall, this open-loop buffer circuit is tailored for high-performance applications in electronic testing and measurement, where rapid response to transient signals is critical for accurate assessments of integrated circuit behavior.An integrated circuit`s response to fast transients on its input supply is often an important measurement to take. If the device under test (DUT) is a micro-power device and doesn`t require an input bypass capacitor, simply drive the power-supply input with a 50 © terminated function generator.
However, as the current requirements and capacitance are increased, this no longer provides acceptable results. One solution to obtaining this fast transient into large capacitive loads is to make an open-loop buffer. Because an open-loop buffer has no feedback, it is insensitive to capacitive loads and can be designed to meet most current requirements.
Important criteria for this buffer include high slew rate, high output drive, low offset voltage, low distortion, and thermal compensation. The circuit in the figure below satisfies these requirements. It is similar to the classic BJT buffer with a few modifications. Because the transistors used are not on a single monolithic die, some means has to be provided to adjust the bias.
Furthermore, the circuit must have some method to keep this bias constant over temperature. The circuit consists of three major blocks. There is a high-impedance complementary input stage, followed by a VBE multiplier for bias adjustment, and then a complementary Darlington output stage. The input stage and the VBE multiplier are biased with constant current sources, whereas the output stage is biased by the output of the VBE multiplier.
The key to connecting the input stage to the VBE multiplier and the output stage is the inclusion of some series resistance via resistors R7 and R8. This allows the VBE multiplier to control the output stage bias without fighting the bias levels of the input stage.
This becomes a factor as the output stage heats up due to load requirements. If the series resistors were not included, the input stage would overbias the output stage at elevated temperatures. Because the VBE multiplier is mounted on the output heatsink, it thermally tracks the output stage, eliminating thermal runaway.
This circuit is designed for bipolar power supplies above the maximum output by about 5V and below the minimum output by about 5V. Operation at +15V and -5V provides good performance. Note that multiple grounds have been included on the board. The input supplies should use a short pair of heavy-gauge wire to the PCB. Do not share these grounds with any other circuitry. The output should be connected to the DUT input with very short heavy-gauge wires. These wires will carry transient currents in excess of 10A and should be sized accordingly. The buffer was designed with a high input impedance to have flexible drive requirements. Don`t connect the output of the buffer to the input of the DUT without a driving signal on the buffer input.
If the output voltages are under ±5V, use a 50 © terminator right at the buffer input. If the output is up to 10V, run the pulse generator unterminated to get this voltage. Voltages beyond this will require the addition of an external amplifier. The maximum supply voltages for the buffer are |V+ - V-| < 40V. 🔗 External reference
An open-loop buffer circuit is essential for applications requiring rapid transient response, especially in environments with significant capacitive loads. The design employs a high-impedance input stage, which minimizes loading on the signal source while ensuring accurate signal reproduction. The VBE multiplier serves as an effective biasing mechanism, adjusting the bias current dynamically based on temperature variations. This feature is critical in maintaining consistent performance across a range of operating conditions.
The complementary Darlington output stage is designed to deliver high current gain, making it suitable for driving loads that require substantial current without sacrificing stability or introducing distortion. The inclusion of series resistors R7 and R8 is a strategic design choice that enhances the circuit's robustness by ensuring that the biasing of the output stage is not adversely affected by changes in the input stage's operating conditions. This design consideration is particularly important in high-power applications where thermal effects can significantly influence circuit performance.
The circuit's layout should prioritize short, direct connections for both power and signal paths to minimize inductance and resistance, which can degrade performance during transient events. The use of heavy-gauge wiring for connections that carry high transient currents is essential to prevent voltage drops and ensure reliable operation. Additionally, careful grounding practices should be observed to prevent ground loops and noise interference, which could compromise the integrity of the measurements taken with the buffer.
Overall, this open-loop buffer circuit is tailored for high-performance applications in electronic testing and measurement, where rapid response to transient signals is critical for accurate assessments of integrated circuit behavior.An integrated circuit`s response to fast transients on its input supply is often an important measurement to take. If the device under test (DUT) is a micro-power device and doesn`t require an input bypass capacitor, simply drive the power-supply input with a 50 © terminated function generator.
However, as the current requirements and capacitance are increased, this no longer provides acceptable results. One solution to obtaining this fast transient into large capacitive loads is to make an open-loop buffer. Because an open-loop buffer has no feedback, it is insensitive to capacitive loads and can be designed to meet most current requirements.
Important criteria for this buffer include high slew rate, high output drive, low offset voltage, low distortion, and thermal compensation. The circuit in the figure below satisfies these requirements. It is similar to the classic BJT buffer with a few modifications. Because the transistors used are not on a single monolithic die, some means has to be provided to adjust the bias.
Furthermore, the circuit must have some method to keep this bias constant over temperature. The circuit consists of three major blocks. There is a high-impedance complementary input stage, followed by a VBE multiplier for bias adjustment, and then a complementary Darlington output stage. The input stage and the VBE multiplier are biased with constant current sources, whereas the output stage is biased by the output of the VBE multiplier.
The key to connecting the input stage to the VBE multiplier and the output stage is the inclusion of some series resistance via resistors R7 and R8. This allows the VBE multiplier to control the output stage bias without fighting the bias levels of the input stage.
This becomes a factor as the output stage heats up due to load requirements. If the series resistors were not included, the input stage would overbias the output stage at elevated temperatures. Because the VBE multiplier is mounted on the output heatsink, it thermally tracks the output stage, eliminating thermal runaway.
This circuit is designed for bipolar power supplies above the maximum output by about 5V and below the minimum output by about 5V. Operation at +15V and -5V provides good performance. Note that multiple grounds have been included on the board. The input supplies should use a short pair of heavy-gauge wire to the PCB. Do not share these grounds with any other circuitry. The output should be connected to the DUT input with very short heavy-gauge wires. These wires will carry transient currents in excess of 10A and should be sized accordingly. The buffer was designed with a high input impedance to have flexible drive requirements. Don`t connect the output of the buffer to the input of the DUT without a driving signal on the buffer input.
If the output voltages are under ±5V, use a 50 © terminator right at the buffer input. If the output is up to 10V, run the pulse generator unterminated to get this voltage. Voltages beyond this will require the addition of an external amplifier. The maximum supply voltages for the buffer are |V+ - V-| < 40V. 🔗 External reference
Related Circuits
The circuit is designed for a broadband linear detection application with a bandwidth of 10 MHz. It serves as a millivoltmeter measuring instrument suitable for frequencies exceeding 10 MHz. The circuit features a linear detector utilizing operational amplifiers, specifically...
Here is a telephone line vigilant circuit to guard against misuse of your telephone lines. It monitors telephone lines round the clock and provides visual as well as an audio warning (when someone is using your telephone lines) which...
A high brightness LED evaluation board has been developed using the Fairchild Semiconductor FAN7554D PWM controller. The evaluation board for high brightness LEDs incorporates the Fairchild Semiconductor FAN7554D PWM controller, which is designed to provide efficient power management and precise...
The current source in the diagram reacts very quickly to changes in the input signal and may be utilized in specific measurements. The differential amplifier IC1 ensures that the voltage across resistor R2 is equal to the input voltage,...
Each component of the circuit is represented in a simple block form with corresponding labels for identification, using no special symbols or language. The interconnections between these components are depicted by solid lines. The block diagrams can be read...
The block diagram illustrates that a 10 MHz signal is generated by an oven-stabilized 10 MHz crystal oscillator, which is locked to a precision 10 kHz signal produced by a GPS receiver module through a phase-locked-loop (PLL) circuit. In...