Electronic Circuits Schematics Projects




Audio splitter amplifier circuit with TL084

Rating: 2.00/10 (91Votes cast)

Category: Inside Circuits
Views: 1631
Rank: 3

The three-channel amplifier output distribution uses a single TL084. The first step is to capacitive coupling with a p. 1.0 ~ electrolytic capacitor. The entries are railways Vee Y2 or 4.5 V. This allows using a single 9 V power supply A voltage gain of 10 (1 M ohm ohm/l00 k) is obtained in the first stage, and the other three floors are connected as a unity gain voltage followers. Each output stage drives independently via an amplifier output 50 pF capacitor to the resistance of 5.1 k ohm load.
Audio splitter amplifier circuit with TL084



The response is flat from 10 Hz to 30 kHz.


Datasheet file1: Click here to download TL084.pdf datasheet.


Related circuits

Digital-frequency-detector

A simple inventer and NAND gate can be connected to yield a highly compact and reliable digital frequency detector. This circuit can detect frequencies up to 3 MHz with 50% duty cycles. When a frequency, j,, appears at the input, points A and B detect a logical high de level. Thereupon pointE...



Preamplifier and high-to-low impedance converter

Thiscircuit matches the very high impedance of ceramic cartridges, unity gain, and low impedance output. By "loading" the cartridge with a 2M2 input resistance, the cartridge characteristics are such as to quite closely compensate for the RIAA recording curve.



Video-line-driving-amplifier

Q1 and Q2 form a differential stage which single- ends into the LT1010. The capacitively terminated feedback divider gives the circuit a de gain of 1, while allowing ac gains up to 10. Using a 20-fl bias resistor, the circuit delivers 1 V pk-pk into a typical 75-fl video load. For...



Single-setpoint temperatre controller

The AD590 produces a temperature-dependent voltage across R (C is for filtering noise). Setting R2 produces a scale-zero voltage. For the Celsius scale, make R = 1 K and Vzero = 073 volts



AC-static SPDT switch

An SPDT solid state relay is shown. When voltage is applied Ql will turn on, activating load #1, because the full line voltage appears across Q2, supplying gate current through Rl. When SI is closed.



Latching burglar alarm II

Closing the protective circuit (R1 to R2) applies positive voltage to the gate of SCR1 and sounds the alarm



Xor-gate-up-down-counter

One can transform an ordinary binary counter, such as a 7493, into an up/down counter with mode control by adding XOR gates 7486 to the counter"s outputs. The circuit counts up when the DN/UP line is low and down when the DN/UP line is high. To use the 7493 counter to count out its maximum...



Fm Modulator Circuit

The FM modulator is built with a Motorola MC1648P oscillator. Two varactors, Motorola MV-209, are used to frequency modulate the oscillator. The 5000- potentiometer is used to bias the varactors for best linearity. The output frequency of approximately 100 MHz can be adjusted by changing the...



Articles & Projects
Video amplifier splitter by transistor BD137-BC547-BC557. This is the video amplifier circuit or the video splitter circuit, it is designed to take video signal is stronger. Compensate for the loss of signal, and is video splitter video, ...

LNA Design Tutorial Series 8 - Wilkinson Splitter. Low Noise Microwave Amplifier Design Tutorial - Part 8. Wilkinson Divider. Today you can find here the Wilkinson power divider design that will be used in the balanced ...

This power amplifier circuit using a transistor amplifier from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A 1500W power amplifier circuits for this.

This power amplifier circuit using a transistor amplifier starting from the front, signal splitter, driver and power amplifier. Current consumption required is quite large power amplifier that is 15-20 A for this 1500W power amplifier ...

Hammonator Organ to Guitar Amp Conversion Circuit Diagram. ... The reverb return level is set with the 100K audio pot and mixed into the phase splitter stage (VT4) through a 5nF capacitor. The clean (non-reverb) signal is amplified by VT7, ...

Repurposing a Televes Satellite distribution amplifier for GPS splitter work. Leave a reply. I was in a ... I then added 220 ohm resistor across each output so the GPS would not report open-circuit antenna. I also changed the ...

A phase-splitting device

Proteus ecc88 tube circuit simulation


Comments




 characters left

Captcha

captchaPlease input letters you see on the image.
Click on image to redraw.



Facebook Comments

Most searched
 
Accounts area
Username:
Password:
Forgot password? Register
Circuits