Timer Circuits
- Page 14-
The cumulative timer circuit consists of resistor R1 and spreadsheet internal crystal oscillator BC, and it is shown as the chart. R1 and R2 choose the metal film resistors: R3 ~ R5 select the 1/8W metal film resistors. C select the aluminum electrolytic.... -
Figure 1 is an improved trigger timing circuit composed of 2 PUT. If you add the set signal, the circuit will be set, transistor VT1 turn to the conduction state, the relay K will be energized action. It supplies voltage for the delay voltage at the same.... -
As shown in the figure is a preset outage timer of electric cooker circuit. Time of the timing circuit ranges from 1 hour to 12 hours, which can be regulated by PR.The timing mode is counting typeand control method mode is preset outage timing. The circuit.... -
The chart shows a function generator circuit composed of 555 timer. The circuit consists of a CH7555 timer and some transistors and RC components. It can generate triangle wave, square wave, sine wave, sawtooth and square wave sweep simultaneously. Ramp can.... -
A very long time constant is provided by R1 and C1. C1 discharges and the near zero voltage at its positive lead is applied to the high impedance inputs of the.... -
One shot multivibrator circuit is also known as monostable multivibrator or timer. The function of such circuit is simply produce a pulse strobe with a fixed.... -
With the help of high gain high impedance operational amplifier, we can build a long time delay with resistor-capacitor (RC) circuit since it allow high.... -
In counter mode it provides 1Hz resolution up to 100Mhz. In timer mode maximum resolution is 0. 0000001 Hz up to 1Hz. Resolution is reduced by one digit for each additional decade. Multiple frequency updates per second by employing a sliding window for.... -
The job of this timer is to disconnect thecompressor circuit and connect a resistive heatingelement located near the evaporator atregular time intervals. The defrost heater is thermostaticallycontrolled and is used to melt any frostformation on the.... -
The Adjustable Timer circuit starts timing when switched on. The green LED lights to show that timing is in progress. When the time period is over the green LED turns off, the red LED turns on and the bleeper sounds. The time period is set.... -
This easy electronic buzzer circuit built based on timer works for gaining the frequency. The IC timer NE 555 used as astable multivibrator operating at about 1kHz and produces a sound when switched on. The sound frequency can be adjusted b.... -
A multivibrator is an electronic circuit used to implement a variety of simple two-state systems such as light emitting diodes, timers and flip-flops. The monostable multivibrator will create a condition: in which one of the states is stabl.... -
The following schematic diagram shows the 12 Volt Car Lamp Dimmer Circuit Design using 555 Timer. This circuit design can be used to dim a standard 25 watt.... -
In this circuit a standard op-amp is wired as an astable multivibrator. The output is non-symmetrical but has the advantage that the timing is controlled by only 1 resistor and capacitor, in this case, the 100k variable resistor, U2 and 100u capacitor C1..... -
These two circuits are multi-range timers offering periods of up to 24 hours and beyond. They can be used as repeating timers - or as single-shot timers. Both circuits are essentially the same. The main difference between them is their behaviour in.... -
This circuit has an adjustable output timer that will re-trigger at regular intervals. The output period can be anything from a fraction of a second to half-an-hour or more - and it can be made to recur at regular intervals of anything from seconds to days.... -
This circuit is based on a simple asymmetric oscillator. The length of time the relay remains energized - and the length of time it remains de-energized - are set independently. With the component values shown in the diagram - both periods are adjustable.... -
This circuit is very similar to Repeating Timer No. 2. However - the addition of the light dependent resistor means that the operation of this timer can be limited to the daylight hours. R7 lets you set the level of light at which the timer will stop. The.... -
This timer is based on a simple Monostable Circuit. The length of time the relay remains energized - the ON period - is controlled by the values of R3 & C2. And the length of time the relay remains de-energized - the OFF period - is controlled by the values.... -
The Cmos 4060 IC has two built-in inverters - at pins 9, 10 and 11. They must be wired together to form an oscillator - the output of which is at Pin 9. While the oscillator is running - Pin 9 is switching continuously from high to low and vice-versa. It`s.... -
This circuit uses a Cmos 4017 decade counter to create a sequence of four separate events. The number of events in the sequence may be increased to nine or ten. And the length of each event is controlled independently. D13 causes the sequence to repeat.... -
This circuit uses a Cmos 4017. The 4017 is a decade counter. The count starts at zero. And it advances by one - each time pin 14 is taken high. When the count reaches nine - it goes back to zero - and starts all over again. = As the count progresses - each.... -
This circuit turns-off an amplifier or any other device when a low level audio signal fed to its input is absent for 15 minutes at least. Pushing P1 the device is switched-on feeding any appliance connected to SK1. Input audio signal is boosted and squared....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Finally, white LED`s are bright enough to use in a practical stroboscope. This circuit can...
This converter enables reception of 800 to 1000 MHz on any scanner covering the 400 to 500-MHz...
This Phone FM transmitter connects in series to your telephone line and transmits the telephone...
Use a relatively high-end microcontroller ( Piccolo TMS320F28035, 12-bit resolution, +/- 4LSB...
The oscillator model I talked about in the introduction to oscillators was as simple as it gets -...
Using a MC14093 CMOS type IC, a quad 2-input NAND Schmitt trigger circuit can be designed a very...
This small amplifier is constructed around the TDA2003 IC, capable of delivering 4Wrms at 4ohms....
The goal of the project is to create a robot that will follow a black line on a white sheet of...
Cheap I2c shown as a bus control stereo decoder TDA9853H. Used for a digital mediation function...
A photosensitive daytime electricity 1B very small positive value. 555 (4) feet (j reset pin...
Configure National Semiconductors DS8877 drive circuit as shown, when the 6 digit calculator and...