Smartcard controlled Lock with Relay
This design uses a smart card to enable a relay. A Nutchip recognizes its mating smart card among thousand similar ones, because you choose the code to be programmed in the card's memory. No specialized knowledge is necessary, as we supply the card program and codes. Nutchip truth table is simple as well, so you should be able to adapt it to your needs (e.g., adding more than one card, or timing the relay). Even in its actual form, the board is ready to work in many useful applications: open gates e.g. for park lots, access control to gyms, swimming pools, tennis play fields, switch on central heating or showers, or the football field lights, enable TV viewing, photocopying, faxing, coffee machine use, telephones etc. Smartcards are very handy as they are compact, lightweight, and require no batteries. Cards are tough compared to remote controls, are resistant to dirt and wet, and don't break apart falling from a tabletop. If a card gets lost or stolen, you can reprogram the Nutchip in minutes, discarding the old code in favour of a new one, therefore making the old card useless. This card-activated relay requires just a handful of parts and is very simple. The active components in addition to the Nutchip are a 74HC00, a reset generator (IC3) and a transistor for relay switching.
The reset integrated circuit IC3, an MC34064 from Motorola, guarantees a clean Nutchip RESET even in presence of electric noise coming from the power network. Its duty consists of discharging the capacitor C2 as fast as possible when a power drop is detected. But let's introduce the smartcard. We choose a "Funcard Purple": this is the usual name for a card embedding a powerful processor, an Atmel AT90S8515, and a serial EEPROM memory. Other "Funcards" similar to the "Purple" are the "Funcard Prussian" and "Funcard Prussian 256": these should be theoretically compatible, although more expensive. However, please note that we have not tried them, so take our word at your own risk.
As the Funcard Purple embeds a microcontroller, it must be loaded with a program written for this specific task before using it in the circuit. The program is a free download from the file "card_1234.hex", and it is supplied ready-made so only a programmer is needed to get up and running. Once programmed, the Funcard's microcontroller will act as a remote control, generating a pulse train indistinguishable from a radio (RF) remote control. The resulting waveform is output on the smartcard pad labelled "OUT," which connects—through a suitable slot connector—to the Nutchip remote control input (REMOTE, pin 6). A series resistor, R4, is placed to protect the Nutchip from noise and spike pulses that can be generated during card insertion and extraction.
The Nutchip (IC1) is the heart of the device. Nutchip output OUT1 drives an LED (LD1) which is in series with a current-limiting resistor (R3). A separate output is used for driving the relay (RELAY1) through a transistorized relay driver stage (TR1, R2, D1). The transistor functions as an electronic switch, amplifying the Nutchip output current from tenths of mA to tens of mA—a level suitable for driving the relay coil. Diode D1 protects the circuits from high voltages that are induced on the coil during switch-off. A quick prototype can be assembled on a breadboard. Despite the small component count, careful attention is required.
Connections should be kept short, ideally less than 10 cm each. A smartcard connector with clearly visible connections is recommended to prevent errors. Colour-coded wiring is encouraged: red for +5V, black for GND, light blue for 4 MHz buffered clock, green for unbuffered clock, and orange for OUT. Care should be taken not to reverse any part: LED, ICs, and the power supply. In case of doubt, the parts pinout should be checked for details.
Before applying power to the circuit, all connections must be verified against the schematic diagram. Once confirmed, the interface can be connected, power switched on, and the Nutchip programmed. Nutstation software should be used to load the truth table "card.nut," selecting the "custom RF" remote control. Key 1 should be clicked, and "1234" input as the key code. This applies if the default .hex file for the smartcard is used; otherwise, the code should be changed accordingly. The Nutchip must then be programmed.This design uses a smart card to enable a relay. A Nutchip recognizes its mating smart card among thousand similar ones, because you choose the code to be programmed in the card's memory. No speacilized knowledge is necessary, as we supply the card program and codes. Nutchip truth table is simple as well, so you should be able to adapt it to your needs (e.g., adding more than one card, or timing the relay).
Even in its actual form, the board is ready to work in many useful applications: open gates e.g. for park lots. access control to gyms, swimming pools, tennis play fields. switch on central heating or showers, or the football field lights. enable TV viewing, photocopyng, faxing, coffe machine use, telephones etc. Smartcards are very handy as they are compact, lightweight, and require no batteries. Cards are tough compared to remote controls, are resistant to dirt and wet, and don't break apart falling from a tabletop. If a card gets lost or stolen, you can reprogram the Nutchip in minutes, discarding the old code in favour of a new one, therefore making the old card useless.
This card-activated realy requires just an handful of parts and is very simple. The active components in addition to the Nutchip are a 74HC00, a reset generator (IC3) and a transistor for relay switching. Thereset integrated circuit IC3, an MC34064 from Motorola, guarantees a clean Nutchip RESET even in presence of electric noise coming from the power network.
Its duty consists of discharging the capacitor C2 as fast as possible when a power drop is detected. But let's introduce the smartcard. We choose a "Funcard Purple": this is the usual name for a card embedding a powerful processor, an Atmel AT90S8515, and a serial EEPROM memory. Other "Funcards" similar to the "Purple" are the "Funcard Prussian" and "Funcard Prussian 256": these should be theoretically compatible, although more expensive.
However, please note that we have not tried them, so take our word at your own risk. As the Funcard Purple embeds a microcontroller, you must load it with a program written for this specific task before using it in our circuit. The program is a free download from the file "card_1234.hex", and we supply it ready made so you need only a programmer to get up and running.
Once programmed, the Funcard's microcontroller will act as a remote control, generating a pulse train undistinguishible from a radio (RF) remote control. The resulting waveform is output on the smartcard pad labelled "OUT, which connects -though a suitable slot connector- to the Nutchip remote control input (REMOTE, pin 6).
We placed a series resistor, R4, in order to protect the Nutchip from noise and spike pulses that can be generated during card insertion and extraction. The Nutchip (IC1) is the heart of the device. Nutchip output OUT1 drives an LED (LD1) which is in series to a current-limiting resistor (R3). A separate output is used for dirving the relay (RELAY1) through a transistorized relay driver stage (TR1, R2, D1).
The transistor works as an electronic switch, amplifying Nutchip output current from tenths of mA to tens of mA - a level suitable for driving the relay coil. Diode D1 protects the circuits from high voltages that are induced on the coil during switchoff. We assembled a quick prototype on a breadboard. Despite the small component count, a great deal of care and attention is required. The photo show a simplified version of the circuit, which does not include the relay, the associated transistor driver, the RESET circuitry.
This is perfectly OK in order to perform many lab experiments before going for a more definitive implementation, like preparing a printed circuit boards and soldering parts (note: PCB drawings not available). Try to keep connections short, always less that 10 cm each, as shown by the photo. If possible, use a smartcard connector with all of the connection are clearly visible, like ours: this will help preventing errors.
Always use colour-coded wiring: our example uses red for +%V, black for GND, light blue for 4 MHz buffered clock, green for unbuffered clock, orange for OUT. Take care not to revert any part: LED, ICs (the photo shows both with pin 1 towards left side), power supply.
In case of doubt, check the parts pinout page for details. When you are finished with the circuit, and before applying power to the circuit, check once more all the connections. If everything corresponds to the schematic diagram, it is time for connecting the interface, switching on power, and programming the Nutchip.
Run Nutstation and load the truth table "card.nut", and select the "custom RF" remote control. From the remote control selection window click on key 1 and input "1234" as the key code. This applies if you are using the default .hex file for the smartcard, otherwise change it accordingly to the new code.Program the Nutchip. 🔗 External reference
The reset integrated circuit IC3, an MC34064 from Motorola, guarantees a clean Nutchip RESET even in presence of electric noise coming from the power network. Its duty consists of discharging the capacitor C2 as fast as possible when a power drop is detected. But let's introduce the smartcard. We choose a "Funcard Purple": this is the usual name for a card embedding a powerful processor, an Atmel AT90S8515, and a serial EEPROM memory. Other "Funcards" similar to the "Purple" are the "Funcard Prussian" and "Funcard Prussian 256": these should be theoretically compatible, although more expensive. However, please note that we have not tried them, so take our word at your own risk.
As the Funcard Purple embeds a microcontroller, it must be loaded with a program written for this specific task before using it in the circuit. The program is a free download from the file "card_1234.hex", and it is supplied ready-made so only a programmer is needed to get up and running. Once programmed, the Funcard's microcontroller will act as a remote control, generating a pulse train indistinguishable from a radio (RF) remote control. The resulting waveform is output on the smartcard pad labelled "OUT," which connects—through a suitable slot connector—to the Nutchip remote control input (REMOTE, pin 6). A series resistor, R4, is placed to protect the Nutchip from noise and spike pulses that can be generated during card insertion and extraction.
The Nutchip (IC1) is the heart of the device. Nutchip output OUT1 drives an LED (LD1) which is in series with a current-limiting resistor (R3). A separate output is used for driving the relay (RELAY1) through a transistorized relay driver stage (TR1, R2, D1). The transistor functions as an electronic switch, amplifying the Nutchip output current from tenths of mA to tens of mA—a level suitable for driving the relay coil. Diode D1 protects the circuits from high voltages that are induced on the coil during switch-off. A quick prototype can be assembled on a breadboard. Despite the small component count, careful attention is required.
Connections should be kept short, ideally less than 10 cm each. A smartcard connector with clearly visible connections is recommended to prevent errors. Colour-coded wiring is encouraged: red for +5V, black for GND, light blue for 4 MHz buffered clock, green for unbuffered clock, and orange for OUT. Care should be taken not to reverse any part: LED, ICs, and the power supply. In case of doubt, the parts pinout should be checked for details.
Before applying power to the circuit, all connections must be verified against the schematic diagram. Once confirmed, the interface can be connected, power switched on, and the Nutchip programmed. Nutstation software should be used to load the truth table "card.nut," selecting the "custom RF" remote control. Key 1 should be clicked, and "1234" input as the key code. This applies if the default .hex file for the smartcard is used; otherwise, the code should be changed accordingly. The Nutchip must then be programmed.This design uses a smart card to enable a relay. A Nutchip recognizes its mating smart card among thousand similar ones, because you choose the code to be programmed in the card's memory. No speacilized knowledge is necessary, as we supply the card program and codes. Nutchip truth table is simple as well, so you should be able to adapt it to your needs (e.g., adding more than one card, or timing the relay).
Even in its actual form, the board is ready to work in many useful applications: open gates e.g. for park lots. access control to gyms, swimming pools, tennis play fields. switch on central heating or showers, or the football field lights. enable TV viewing, photocopyng, faxing, coffe machine use, telephones etc. Smartcards are very handy as they are compact, lightweight, and require no batteries. Cards are tough compared to remote controls, are resistant to dirt and wet, and don't break apart falling from a tabletop. If a card gets lost or stolen, you can reprogram the Nutchip in minutes, discarding the old code in favour of a new one, therefore making the old card useless.
This card-activated realy requires just an handful of parts and is very simple. The active components in addition to the Nutchip are a 74HC00, a reset generator (IC3) and a transistor for relay switching. Thereset integrated circuit IC3, an MC34064 from Motorola, guarantees a clean Nutchip RESET even in presence of electric noise coming from the power network.
Its duty consists of discharging the capacitor C2 as fast as possible when a power drop is detected. But let's introduce the smartcard. We choose a "Funcard Purple": this is the usual name for a card embedding a powerful processor, an Atmel AT90S8515, and a serial EEPROM memory. Other "Funcards" similar to the "Purple" are the "Funcard Prussian" and "Funcard Prussian 256": these should be theoretically compatible, although more expensive.
However, please note that we have not tried them, so take our word at your own risk. As the Funcard Purple embeds a microcontroller, you must load it with a program written for this specific task before using it in our circuit. The program is a free download from the file "card_1234.hex", and we supply it ready made so you need only a programmer to get up and running.
Once programmed, the Funcard's microcontroller will act as a remote control, generating a pulse train undistinguishible from a radio (RF) remote control. The resulting waveform is output on the smartcard pad labelled "OUT, which connects -though a suitable slot connector- to the Nutchip remote control input (REMOTE, pin 6).
We placed a series resistor, R4, in order to protect the Nutchip from noise and spike pulses that can be generated during card insertion and extraction. The Nutchip (IC1) is the heart of the device. Nutchip output OUT1 drives an LED (LD1) which is in series to a current-limiting resistor (R3). A separate output is used for dirving the relay (RELAY1) through a transistorized relay driver stage (TR1, R2, D1).
The transistor works as an electronic switch, amplifying Nutchip output current from tenths of mA to tens of mA - a level suitable for driving the relay coil. Diode D1 protects the circuits from high voltages that are induced on the coil during switchoff. We assembled a quick prototype on a breadboard. Despite the small component count, a great deal of care and attention is required. The photo show a simplified version of the circuit, which does not include the relay, the associated transistor driver, the RESET circuitry.
This is perfectly OK in order to perform many lab experiments before going for a more definitive implementation, like preparing a printed circuit boards and soldering parts (note: PCB drawings not available). Try to keep connections short, always less that 10 cm each, as shown by the photo. If possible, use a smartcard connector with all of the connection are clearly visible, like ours: this will help preventing errors.
Always use colour-coded wiring: our example uses red for +%V, black for GND, light blue for 4 MHz buffered clock, green for unbuffered clock, orange for OUT. Take care not to revert any part: LED, ICs (the photo shows both with pin 1 towards left side), power supply.
In case of doubt, check the parts pinout page for details. When you are finished with the circuit, and before applying power to the circuit, check once more all the connections. If everything corresponds to the schematic diagram, it is time for connecting the interface, switching on power, and programming the Nutchip.
Run Nutstation and load the truth table "card.nut", and select the "custom RF" remote control. From the remote control selection window click on key 1 and input "1234" as the key code. This applies if you are using the default .hex file for the smartcard, otherwise change it accordingly to the new code.Program the Nutchip. 🔗 External reference
Related Circuits
This project outlines a digital clock featuring an alarm function, utilizing a PIC16F877 microcontroller to achieve an accurate 1-second delay with Timer0 through Roman's zero error method. The time is displayed in large font on a 4G—20 character LCD,...
The image below depicts a block diagram of a complete mixer that consists of four input amplifier modules followed by four switchable tone management modules, one stereo line input, four mono main faders, one stereo dual-ganged main fader, four...
This experiment can be constructed using a single 8-position DIP switch, but utilizing two switch assemblies enhances the understanding of the concept. One switch assembly retains the correct code for unlocking the lock, while the other serves as the...
The Analog Devices 1831 is designed for strain gauge signal conditioning applications. It features an internal low drift input of 0.25V with a gain of 1000, exhibiting excellent linearity with a maximum deviation of 0.005%. The IC operates with...
When the telephone rings or when the handset is lifted, the night light is activated and remains illuminated during the conversation. After the handset is replaced in the cradle, the light stays on for approximately 11 seconds. Under standby...
Author Mazi Hosseini describes a simple, low-cost voltage-controlled current source using two operational amplifiers that provides a good range of current and maximum load. The circuit described by Mazi Hosseini utilizes two operational amplifiers (op-amps) to create a voltage-controlled current...