Television Circuits
-
Desheng 1012 12-band FM, MW, SW, TV sound radio circuit diagram as follows: .. -
This Circuit uses the ZNA234E IC which makes available all the waveforms necessary to produce the crosshatch, dot and greyscale test patterns on a television screen. The composite video output can be injected directly into the video input of a receiver or.... -
The amplifier picks up the TV"s audio output signal and amplifies it to drive a set of earphones for private listening. It is built around an LM324 quad op amp and an LM386 low-power audio amplifier. .. -
This circuit provides a simple, low-cost crosshatch generator tor convergence and geometry adJUStments on color TVs. The generator is driven by two clocks, one for the horizontal drive, IC1ab, and one for the vertical drive, IC2ab. The clock outputs are.... -
The composite input signal is preamplified by transistor Ql and is then coupled to the high-pass filter composed of C3, C4, R6, and R7. The filtered audio is then passed to IC1, an MC1310P "Coilless Stereo Demodulator." That IC is normally used to demodulate.... -
A PAL color encoder and video summer which requires just composite sync and composite blanking inputs, and a 6-bit binary coded input giving the color information. The inputs are organized as 2 bits per primary color with gamma correction automatically.... -
A pattern generator is a very useful instrument for the correct alignment of the timing circuits of a television set. The circuit we propose you to build, is a «bar generator» that will produce horizontal and vertical stripes (bars) on the TV screen, that.... -
When measure video signal with oscilloscope, video line selector is very useful to find a scan line. The line selecter generates trigger pulse at selected line, oscilloscope will display only selected line. This is a very simple video line selector... -
The amplifier in Figure 1 originally served as the photomultiplier preamplifier in a Doppler system intended for eventual operation in the Martian atmosphere. The design is based on a switchable array of six Maxim MAX4258 dual-channel video.... -
I've seen an NE592 used as a video buffer amp at the end of a 75 ohm line. Used so that the 75 ohm line could drive all kinds of neat processing stuff without affecting the signal (that's what a buffer is after all, right?) Now National Semiconductor makes.... -
Recently, most digital video equipments, such as video recorder, DVD player and TV game, have component video output. The component video signal is like RGB video signal, but it cannot connect to RGB monitor directly. Thus I designed and built YUV(YCrCb) to.... -
The compact high performance 4 x 4 crosspoint shown in Figure 1 uses four LT1205s to route any input to any or all outputs. The complete crosspoint uses only six SO packages, and less than six square inches of PC board space. The LT1254 quad current feedback.... -
Crosspoint switches are ideal for use in video-security systems, which accept multiple camera inputs while providing playback and multiple loop-through to multiple monitors. To provide video loop-through or monitor outputs, these systems often require....
-
This design note presents a voltage controlled cable equalizer based on the LT1256 video fader. The circuit features ease of adjustment, simplicity and the capability for remote control. The amount of equalization can be adjusted continuously from the....
-
The first idea they was to work with 8.867238 MHz crystal (2 times the color carrier). When I read more about PAL video composite signal creation, I saw that, if you want to product colors entire-in-software you must to create the color-carrier (4.43 MHz),.... -
When you`re copying videotapes, it`s sometimes desirable to suppress some passages. Using the pause control of the recorder does not yield satisfactory results. Another method produces better results (Figure 1). The video source connects to the video-in....
-
A number of single-chip VGAs variable-gain amplifiers are available today. Unfortunately, they all have drawbacks, such as high noise, 55V limit, low input impedance, or nonlinear gain/frequency characteristics. The circuit in Figure 1 is a 16-step,....
-
The difficulty of connection vga of a videocard to the TV set is, that Frequency of lower case development(display) of the TV set makes 15 KHz, and VGA card - from 31 KHz and is higher. Translation of development(display) of the TV set up to 31 KHz.... -
The technique applies to highpass filters. You derive a composite highpass filter by using m-derived terminating half-sections with one or more constant-k interior full sections. Classic image-parameter design used m-derived half-sections with m=0.6 for best....
-
A crucial point in the design is the input/decoder section, and the question of what ICs to use for decoding the input video to component digital video streams. The choice for this project was the Philips IC SAA7114H, new on the market at the time. This chip....
-
A 2N3904 in the base circuit sets the `Q' point of the amplifier. FM subcarrier audio at 4.5 MHz is also injected at this point through a 3300 ohm resistor and a DC blocking capacitor. A high frequency 5-watt RF power transistor (2SC1909) serves as the last.... -
The 12VDC supply provides power for the camera and video modulator circuits. The video from the camera is fed into the video input of the modulator circuit. The modulated RF from the modulator is fed into a small antenna. Use of a dipole antenna that is.... -
Video designs are often pressed to operate on the lowest possible rail voltagesa simple result of the trend towards lower voltage logic and the advantages of sharing supply potentials wherever possible...
-
VID2G project is an PAL/NTSC color generator & video identifier with digital sync regeneration, digital PLL, video Squelch output, predefined video pages, keyboard & full RS-232 access, etc. Dynamic and fixed ID`s, user positions, user selectable....
-
This is a very basic circuit for fading video signal shown in Eletor Electronics magazine. You can use this between two video equipments. The circuit is so simple that the impedance matching and some other things are not exactly correct, so might not always....
-
The block diagram in Figure 1 shows how to make a cable-free, direct-video system. The system allows users to walk from booth to booth at an exhibition to interview people and to display the interviews in real time on three screens at key locations...
-
Often you can get away with running a monochrome monitor on GREEN, but this looks real crappy when viewing color images. These simple resistor networks allow you to display R+G+B on a B/W or CCTV monitor without ghosting. Be shure to set your video card for.... -
Test signals inserted in the lines of the vertical blanking interval, defined by the TV standard, e. g. for the 625 standard the CCIR together with the EBU issued the formal specifications for the signals inserted in lines 17, 18, 330 and 331... -
The idea to produce a standard TV PAL signal using a SVGA graphics card was born a few years ago, where cheap graphics cards with TV output were still not available. To achieve a CCIR conform TV signal with 50 Hz vertical interlaced refresh and 15.625 kHz.... -
This design was published in the June 1994 issue of Electronics Australia, and has proven extremely popular. The kit was sold by Jaycar Electronics, but has since been discontinued. It is a simple device that connects between your keyboard and VGA card.... -
The synchronous oscillator (SO) and the coherent phase-locked synchronous oscillator (CPSO) are universal multifunctional networks that track, synchronize, and amplify as much as 80 dB; improve SNR by as much as 70 dB; and modulate AM, FM, and FSK signals...
-
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
A device designed for measuring time and temperature used in chemistry laboratory. The circuit...
The composite input signal is preamplified by transistor Ql and is then coupled to the high-pass...
1. THE INPUT CLOCK frequency fed into this circuit is divided by 2n-l. The circuit consists of...
The video circuit illustrated in Figure 1 combines an audio-subcarrier notch filter and...
FM transmitter or often called fm transmitter uses 2 transistors in this article uses 2...
Audio Level Meter Description A simple and low cost audio level meter circuit that can be used to...
The sensors are a thin strip of piezoelectric material with a rivet in the end acting as a...
Also called the parallel A/D converter, this circuit is the simplest to understand. It is formed...
This is a project that I undertook during June 1996 as my final year electronics project. The...
Provides timing in seconds to 99 s, and timing in minutes to 99 min, with 2-digit LED indicator...