Audio Amplifier Circuits
- Page 27-
A small power amplifier, but with very good quality of sound. It combines a completed very good quality (NE5534), that has the possibility of control of low loads, high speed, low distortion and two transistors of technology v-mosfet in the exit.... -
It is a little collection of amplifiers in bridge connection. The output power is low and they are for general use. They can be used with small active loudspeakers, car stereos etc. The only restriction, is that we should use loudspeakers with resistance.... -
The circuit is simple, yet is capable of excellent performance. I designed it specifically for use as an amplifier for the digital sound card in my computer. Audio input can be from any two-channel line level device such as a television, CD player, or VCR..... -
A opamp medium power, used as amplifier of headphones with possibility drive low loads. It contains in a nutshell two amplifiers. The voltage gain, has been determined in 40dB, from the R3-4 and R11-12, for each channel, respectively. The restriction of.... -
Even if simple the circuit, plirej` all condition, regarding the distortion and the response of frequency. The resistance of entry is 250K and the load that can drive is between 100R and 2K.... -
It`s a classic designing of final amplifier 35 W, with two EL34 in push-pull, from the Siemens and Halske, with year of designing 24/3/1953 and code SV410/1. The amplifier it worked from 1954 until 1989, whenever it came also out except operation, with mean.... -
The example below illustrates using an op-amp as an audio amplifier for a simple intercom. A small 8 ohm speaker is used as a microphone which is coupled to the op-amp input through a 0.1uF capacitor. The speaker is sensitive to low frequencies and the small.... -
This circuit is similar to the one above but uses positive feedback to get a little more amplitude to the speaker. I copied it from a small 5 transistor radio that uses a 25 ohm speaker. In the circuit above, the load resistor for the driver transistor is.... -
2 x 18W Hi-Fi Stereo Power Amplifier based around two TDA2030 ICs. It has good input sensitivity, low distortion, good operating stability and full protection against overloads and output short-circuits. It can be used as a booster amplifier for existing.... -
This is a 25 Watt basic power amp that was designed to be (relatively) easy to build at a reasonable cost. It has better performance than the standard STK module amps that are used in practically every mass market stereo receiver manufactured today.... -
This amplifier was designed to be self-contained in a small loudspeaker box. It can be feed by Walkman, Mini-Disc, iPod and CD players, computers and similar devices fitted with line or headphone output. Of course, in most cases you will have to make two.... -
It`s based on a Philips class-H audio amplifier IC and can deliver 36W RMS OR 70W music power, all from a 13.8V supply. Our new Mighty Midget Amplifier can really pack a punch - around 36W RMS continuous into a 4-ohm load when using a 13.8V supply. However,.... -
In the original circuit, a three-diode string was wired in series to R10. Two of these diodes are now replaced by a red LED in order to achieve improved quiescent current stability over a larger temperature range. Thanks to David Edwards of LedeAudio for.... -
Using this low-cost project one can reproduce audio from TV without disturbing others. It does not use any wire connection between TV and Loud Speaker. In place of a pair of wires, it uses invisible infra-red light to transmit audio signals from TV to Loud.... -
Designs for audio amplifiers with DC coupling to the load are not often encountered these days, even though they offer definite advantages.... -
Some lovers of High Fidelity headphone listening prefer the use of battery powered headphone amplifiers, not only for portable units but also for home "table" applications. This design is intended to fulfill their needs. An improved output driving capability.... -
The mentioned shunt-feedback configuration also allows the easy addition of frequency dependent networks in order to obtain an useful, unobtrusive, switchable Tilt control (optional). When SW1 is set in the first position a gentle, shelving bass lift and.... -
Apart from the obvious usage as a headphone amplifier, the circuit can be used for a range of applications where a wide bandwidth low power amplifier is needed. The circuit is based on an opamp, with its output current boosted by a pair of transistors.... -
The amplifier`s gain is nominally 20 dB. Its frequency response is determined primarily by the value of just a few components-primarily C1 and R1. The values of the schematic diagram provide a response of ±3. 0 dB from about 120 Hz to better than 20, 000 Hz..... -
Class D audio power amplifier schematic diagram with TDA7480, capable of 10W output power at a load of 8w/4w and a total harmonic distorsion of 10%. Requires a split-supply (max. ±20V).... -
The combination of the LM4651 driver IC and the LM4652 power MOSFET Class D power amplifier IC provides a high efficiency amplifier solution, suitable for self-powered speakers, subwoofers and quality car boosters. The LM 4651 is a fully integrated.... -
7W Mono Audio Amplifier Kit - This small amplifier is constructed around the TDA2003 IC, capable of delivering 7 watts music power into 4 ohms.... -
TDA2003 has improved performance with the same pin configuration as the TDA 2002. The features of TDA 2002 - very low number of external components, ease of assembly, space and cost saving - are maintained. The device provides a high output current.... -
The Tda2005 IC has a high output power: PO=10W+10W @ RL=2ohm, d=10% (stereo) and PO=20W @ RL=4ohm, d=1% (bridge) for Vs=14. 4V. The high reliability of the IC comes from the various protections against: output DC and AC short circuit to ground, overrating.... -
Class D amplifiers are much more efficient than other Classical amplifiers, but their high efficiency comes at the expense of increased noise and distortion. You can assess the frequency- and Time-domain characteristics of a Class D amplifier, including the.... -
This device has 24 milliwatts quiescent power drain when operating from 6 V supply in which making the LM386 ideal for battery operation. It is stated in the application hints section ofLM386 datasheet, there are two pins (1 and 8 ) provided for gain control.... -
This circuit be signal sound expansion from condenser microphone give with small-sized loudspeaker. It compose the importance is part pre mic use transistor just one enlarge sound signal gives the power goes up change come to a part amplifier with the.... -
The following circuit diagram is a simplified application circuit of the TDA8932B/33(B) device when operated from an asymmetrical supply (single supply). Here`s the circuit diagram: To simplify the design for an asymmetrical supply in SE configuration, the....
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
The expander to complement the compressor is shown. An external op amp is used for high slew...
Buffered video amplifier is used wherever the use of video player to the receiver / monitor TV...
This circuit is design circuit for a differential analog circuit switches. The FM1208 monolithic...
Typically the input protection fuse of your DMM will blow in the middle of a demonstration or an...
A very useful application of the 565 PLL is as a FSK demodulator. In the 565 PLL the frequency...
The Global Positioning System (GPS) relies on more than two dozen GPS satellites orbiting the...
MAX420 is a monolithic chopper OP amplifier supply voltage is 15 V (ICL76s0 supply voltage of...