Microphone Circuits
- Page 4-
This circuit was submitted and design by Lazar Pancic from Yugoslavia. The sound card for a PC generally has a microphone input, speaker output and sometimes line inputs and outputs. The mic input is designed for dynamic microphones only in impedance range.... -
This circuit is allows you to use a cheap loudspeaker as a microphone. Sound waves reaching the speaker cone cause fluctuations in the voice coil. The voice coil moving in the speakers magnetic field will produce a small electrical signal. The circuit is.... -
The TS-440S, like probably a number of other radios, does not mute the microphone while you are using the rear audio connector for digital modes. So, unless you unplug the microphone each time you want to use the digital modes, shack noises will get on your.... -
This is a simple microphone preamplifer circuit which you can use betw1een your microphone and stereo amplifier. This circuit amplifier microphone suitable for use with normal home stereo amplifier line/CD/aux/tape inputs. This mic preamp can take both.... -
This design was born of frustration with the mic preamp in my Sony R91. It clips at ridiculously low levels, basically it has 28mV of headroom to deal with an input that could be as high as 1800mV (depending on mic & volume), so this design attempts to cure.... -
An amplifier is something that amplified the voltage on a circuit. The most basic kind is an operational amplifier, and this video will show you how these work and how to use them in your electronics. As an example you`ll learn how to make a microphone.... -
FM Wireless Microphone Schematic. In some applications, the use of the microphone cable is sometimes very difficultly. So use a cordless microphone is needed. Microphone as it is often referred to as wireless microphones (cordless microphone). Here I share.... -
This is a design circuit for a stereo amplifier for a high sensitivity stereo parabolic microphone. This circuit can be used for listening to distant sounds. Typical parabolic microphones are mono phonic, this unit has a stereo audio path that helps produce.... -
CAD`s original E100 microphone was an inexpensive (for its time) multi-purpose studio condenser microphone, with an electret capsule and a neutral sound profile. Part of CAD`s Equitek series, the E100 had an innovative transformerless amplifier circuit.... -
The mic`s capsule is believed to be a 32mm OD, 26mm diaphragm design with 3-micron membranes. It is most likely the standard Chinese-made 32mm K67 capsule found in most inexpensive imported condensers... -
The M7 capsule is a center-terminated, dual-diaphragm design, and supports three polar patterns. A switch on the power supply allows selection of Cardioid, Figure-of-8, or Omnidirectional patterns. The amplifier circuit is similar to some of Gefell`s.... -
Both mics, along with the stereo mics SM2 and SM23, used the same basic capsule design ” which itself was very similar to the KM54 capsule. According to Klaus Heyne of German Masterworks, the FET KM88 was designed in order to use up the company`s surplus of.... -
Both used a pair of capsules from Neumann`s K67 family, mounted one atop another, with the top capsule having the ability to be rotated 270 ° against the bottom (presumably, -90 ° +180 ° like the USM 69). The capsule is Neumann`s K870, a 34mm design with.... -
The Neumann/Gefell UM 57 was a large-diaphragm tube condenser microphone manufactured by the Neumann company of Gefell, Germany, currently known as Microtech-Gefell. The mic used the Gefell company`s famous M7 capsule. This was a dual-diaphragm,.... -
The MK-219 is a popular large-diaphragm condenser, designed and produced in JSC Oktava`s factory in Tula, Russia. Since its release (in the West) in 1994, it has had a reputation of offering a great value for the price, which at the time was over $500. These.... -
The MK-319 is a fixed cardioid-pattern, large-diaphragm condenser microphone. The capsule assembly is the same as the MK-219; the primary differences between the models are: The diaphragm is gold sputtered teflon, mounted to a center-terminated capsule.... -
The Sennheiser MKH 415 T is a medium shotgun microphone, powered by the 12VDC A-B standard (aka DIN 45 595, aka T power). It was the forerunner to the popular MKH 416, which is still made. According to Sennheiser lore, the original MKH 415 prototype was.... -
The Mk II was a second-generation version of the TG X 50. Both were dynamic microphones intended for bass instruments and kick drums. The primary difference between the two versions was the introduction of a passive EQ filter in the Mk II. Note that the.... -
Both transistors should be low noise types. In the original circuit, is used BC650C which is an ultra low noise device. These transistors are now hard to find but BC549C or BC109C are a good replacement. The circuit is self stabilizing and will set its.... -
The sound card for a PC generally has a microphone input, speaker output and sometimes line inputs and outputs. The mic input is designed for dynamic microphones only in impedance range of 200 to 600 ohms. Lazar has adapted the sound card to use a common.... -
Microphone problem on Nokia 6630 usually caused by several reason, damaged microphone, broken path or line, and damaged the UEM IC. If the problem caused by the broken path in the microphone circuit, we need the Nokia 6630 schematic diagram to find the.... -
This is a simple circuit that can detect sounds by using a common condenser microphone. Sensitivity is variable. The circuit`s output becomes High each time a sound is detected, otherwise it is in low level. You can use it in simple robots for sound.... -
These require power to work. Sometimes, that`s a battery you put into the mic. Sometimes it`s a separate dedicated power supply with a special multi-pin cable. But most often these microphones use phantom power. This is power deliveredby a mixer or console,....
Neighbour Categories
New Circuits
-
This project fits more for custom made battery casing that can have more space to hide things inside. This switch with few alterations can be used for any other project as well but is designed based on e-bike needs! This project use a clever functionality of.... -
The circuit described here uses ultrasonic oscillations and operates based on the propagation velocity of these oscillations in the air. Thus, we can easily determine the distance of two points if the time within which the wave travels this distance is.... -
Sometimes the precious metals are hidden too deep and are not detected except with complicated devices. In many cases, however, small pieces of precious metal buried near the surface can be detected by relatively simple means. Everyone is very attractive to.... -
Many times for various reasons we forget or can not water the plants that we have in our homes. And many humidity sensors units just notify us with a beeping sound or with a flashing light, that the pot needs watering. But what if we are away from home? This.... -
The principle behind a metal detector is really very simple. Proof of this is the circuit that follows, in which it proves that the construction of a metal detector can be done in the minute, with few components that we find very easily everywhere. With the.... -
The sub-harmonic bass generator is a sound producing unit for guitars. The sound it produces looks very much like that of the bass guitar. The octave generator is sometimes quite unusual since it does not produce any of the usual ways of coloring the sound,.... -
In the past the sounding (sea bottom measurement) was done with the "bullet", that is, with a heavy lead object that the seamen plucked into the sea hung from a calibrated rope. As soon as the "bullet" reached the bottom, the depth appeared directly from the.... -
This Amplifier was designed to have the following specifications: Distortion less than 0.1% at full power of 100W even at 20KHz. Power has to be attributed to an extended bandwidth. The output transistors must be protected against short circuits. The power.... -
A series of LEDs serve to alert the gardener when plants need water. Using two conventional digital integrated LEDs and a series of LEDs, we make a very useful device for gardening. The device detects the amount of water in the pot and alerts the grower.....
Popular Circuits
Often a need arises for connection of two telephone instruments in parallel to one line. But it...
This voltage-to-frequency converter (VFC) accepts the bipolar-ac inputs. For -10- to + 10-V...
Browse » home » alarm » circuit » explanation » latest » schematic » siren » wailing » with »...
Flash slaves are used when you need to supplement one flash unit with one or several more. This...
This is a constant current source using a FET. This is the most simple replacement to series...
A dimming control circuit generates a dimming control signal for determining brightness of at...
This magic lamp appears to be an ordinary frosted light bulb with a rather unusual...
With sine-wave input, RCA CA3046 transistor array connected as VCO can be used as low-distortion...
The circuit will provide a 20 ±0. 1 dB voltage gain from 500 kHz to 50 MHz. The low-frequency...